€J !:iC:lc:Jrl

iQ

2015 PRE-DELIVERY SERVICE CHECK SHEET

IU

B EFORE INSPECTION

5

01 Install DCC fuse (see page 2) ......................... .. ... ... ......
02 Install rad io antenna* .... ...... ........................ .............. .... .. .

D
D

01 Rem ove disc brake anti-rust covers/anti-corros ion
wheel film* .......................................... ............................
02 Activate and initialize Tire Pressure Warning System
(TPWS) (see page 2) .... .................................. ..... ...........
03 Inspect tires for defects/damage .......................... ....... ....
04 Install wheel covers/caps/spare tire wheel covers• ...... ....
05 Install rubber body plugs (stored in glove box) ..............
06 Inspect for fuel, oil, coolant, and other fluid leaks ............
07 Visua lly check bolts and nuts on chassis and powertrain
for looseness ......................... ..........................................
08 Inspect under the veh icle for damage, rust, etc .... ....... ....
09 Install front wheel opening extension pads ...............

FUNCTIONAL OPERATION
Apply parking brake and cycle ignition "JG-ON,· place gear selector in reverse tum
on lights and rear defogger Unlock all doors, release fuel door, re lease trunk hatch

01
02
03
04
05
06
07
08

Check dome, courtesy, map, and sun visor lights· ..........
Check warning/indicator lights, gauges, and horn ...........
Check windshield wipers and washers ............................
Check headlights, instrument lights, turn signals,
dimmer switch , emergency flashers, and brake lights .....
Check inside/outside rear view mirror operation/
adjustment... ................ ........ .......... .. ............ ....................
Check power outlet* and cigarette lighter ........ ... ............
Check audio/navigation· systems, set SSP' to iQ and
set clock ........................................................... ... ....
Install shift-lock override button cover ... ... ................ ......

DD
DD
DD
DD
DD
DD
DD
D

.a~
~a:

D
D
DD
D
D
DD
DD
DD
D

Enter Odometer Reading
Reading After Test

01
02
03
04
05
06

Check cold engine operation ...........................................
Check engine operation during warm-up ................. ..... .. .
Check engine at normal operating temperature ......... .. ...
Check automatic transmission operation ............. ............
Check brake and parking brake operation ................. .. ....
Check steering operation and off-center/vehicle
pull/flutter ............ .. ........ ....... ... ...... ..... .... ........ ..... ......... ....
07 Inspect for abnormal noise and vibration ..... ...... .. ............
08 Inspect for squeaks and rattles ......... ................... ............
09 Check heater and NC operation ....... ............... .......... .....
1O Check speedometer operation ........ ....... ... ..... .. ... .. ..........
11 Check cruise control operation ......... ..... ..........................

Start at left front door Check window and door lock operation (from master power
switch, if eqwpped) Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat belts, interior
condition, all lights, luggage compartment contents Finish by checking headlight
aim and continue into UNDER HOOD checks.

DD
DD
DD
DD
DO
DD
DD
DD
DD

DO
DO
DD
DD
DO
DD
DD
DO
DD
DO
DD

FINAL INSPECTION AND CLEANING
01 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove protective covers just before delivery
to customer) .... .... .. .. ..... .............. ...... ..... ..........................
02 Verify floor m at application and install us ing
retaining cl ips* ..................................... ..........................
03 Visually inspect all interior parts for installation,
damage, fit, dirt, etc............ .............................................
04 Remove Rapgard™ film & clear protective bumper film* .
05 Wash and clean vehicle ...... .................. .. ............. ....... .....
06 Inspect paint finish for scratches, chips, rust, dents,
damage, etc..... ................... .. .... .. ............. ........ ................
07 Inspect exterior body parts for proper installation,
damage, rust, etc........ ... ........... .... ............... ........ .... ........
08 Place Owner's Guide and first aid kit portfolio*
in glove box ......................................... ...........................
09 Place oil change sticker on inside of windshield, top
left corner .... ................................................. ... ................
10 Perform Techstream Health Check .. ..... ... .. .... ... .. ..........
11 Install front license plate or cover• (see page 2) .............

UNDER HOOD
Check engine oil and ATM fl uid levels .............................
Check brake fluid level. .......... ... .... .... ............. ........... .......
Check engine coolant level. ..... .. ..... ................ .................
Check windshield washer fluid level ............................ ...
Check battery state-of-charge using Digital Battery
System Analyzer (SOC Reading :
%) .....
06 Inspect for fuel , oil, coolant, and other flu id leaks ...... ......

I;.

A complete road test helps assure customer satisfaction Drive vehicle over a
variety of road surfaces and dnv1ng cond1t1ons Check for unusual noise and
driving performance

Reading Before Test

01 Check door and door lock operation, including each
wireless remote control/theft deterrent system• .......... ...
02 Check power window operation ...... ...............................
03 Check that engine starts with all keys ............................
04 Check seats and seat belt operation ............. ...... ..... .. ....
05 Check rear defogger ................................. .....................
06 Check side marker, tail, backup, and license plate lights
07 Check rea r hatch/cargo area trim appearance ...............
08 Check tire repair kit and tool installation .... ..... ...... ..........
09 Check headlight aim . ················ ········· ·· ···· ·· ···· ······· ··········

ii::

0

ROAD TEST

WA LKAROUND INSPECTION

01
02
03
04
05

UNDER VEHICLE (ON HOIST)

August 201 4

DD
DD
DD
DD
OD
DD

Comments

.

D
DD
DD
D
D
DO
DD
D
0

DD
D

Ins p ect or install w he n equip ped/req uired.

Completion and retention of this form is required to comply with Toyota's Warranty Policy

TECHNICIAN'S SIGNATURE

SERVICE MANAGER'S SIGNATURE

NAME (PLEASE PRINT)

NAME (PLEASE PRINT)

Date

I

Dealer Name

I

Dealer Code

We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.

I

Vehicle ldenl1ficat1on N umber (Sticker)

DCC FUSE INSTA LLA TION
To minimize battery discharge the DCC fuse has been removed and is
stored in the engine compartment relay block. Install the DCC fuse (30A)
and confirm all related DTCs are cleared.
OTC Clearing Procedure
1. Connect Techstream .
2. Cycle the ignition switch to the "IG-ON" position.
3. Using Techstream , check any other codes being output.
4. Erase DTCs (81650 and 81794) and Freeze Frame Data.
NOTE
If any DTCs besides 81650 and 81794 appear, repair the
applicable system according to the Repair Manual.

1 Remove DCC Fuse (30A)
2 Install DCC Fuse (30A) Here

TIRE PRESSURE WARNING SYSTEM (TPWS) ACTIVATION AND INITIALIZATION
Activat ion Procedure
1. Connect Techstream.
2. Cycle the ignition switch to the "IG-ON" position and check that the Low Tire Pressure Warning Lig ht blinks for 1 minute
and then remains illuminated.

3. Press or remove the valve core to reduce the tire inflation pressure rapidly by 6 psi (0.4 kfg/cm 2 , 40 kPA), or more, within
30 seconds.
4. Check that the Low Tire Pressure Warn ing Light goes OFF after all the TPWS sensors are activated.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature, perform a
Health Check using Techstream and select th e "Compensation Tire Pressure" checkbox. Compensation pressures will be
displayed on the Health Check results screen . Adjust the tire pressure when the tires are cold .
5. Using Techstream, check for DTCs (C2111-C2114) . If no DTCs are stored, continue to Initialization procedure. If these
DTCs are stored, repeat step 3.
Initialization Procedure
Refer to the Repair Manual fo r the Initialization procedure.

FRONT LICENSE PLATE OR COVER INSTALLATION*
For states that require a front license plate, follow the front license plate
installation procedure below. For states that do not requ ire a front license
plate, follow the front license plate cover (stored in the luggage
compartment) installation procedure .
Front License Plate Installation Procedure
1. Align the installation holes on the front license plate with the dimples
on the front bumper.
2. Direct ly screw 2 self-tapping screws into the dimples to install th e
front license plate .
Use self-tapping screws of a non-corroding type with the following
dimensions.

1 Dimples
2 L icense Pl ate

3 Self-tapping Screws

1 Spring Nuts/Bumper Holes
2 Plastic Clips
3 License Plate Cover

4 Adhesive Tape Contact Location
5 Adhesi ve Tape (Backside of
Cover)

Nominal Length: 15.0 - 20.0 mm (0.60 - 0.79 in.)
Diameter: 6.0 mm (0.24 in.)
Front License Plat e Cover Installat io n Procedure
1. Remove the 2 metal spring nuts from the bumper cover and discard.
2. Clean the area where the license plate cover adhesive w ill contact
t he bumper.
3. Attach the 2 plastic clips to the license plat e cover.
4. Remove the 2 strips of adhesive cover from the license plate cover.
5. Insert the plastic clips into the bumper cover holes.
6. Ensure the adhesive strips contact the bumper by pressing on the
edges of the license plate cover.