@TOYOTA RAV4
2015 PRE-DELIVERY SERVICE CHECK SHEET
x:

BEFORE INSPECTION

0

01 Install D/C Cut Fuse (see p ag e 2)........ .............. ... ....... ..
02 Install antenna* ...... .............................................. .... ........

I

il,,,
.a~

UNDER VEH ICLE (ON HOIST)

:;!a:

01 Remov e disc brake anti-ru st covers/anti -corrosion
wheel film* ................................. -............ ..................... ..
02 Inspect tires for defects/damage and adjust air pressure
(including spare tire) ......................................................
03 Initialize Tire Pressure Warning System (TPWS) (see
pag e 2) .......................................... .......................... . ....
04 Install wheel covers/caps/spare tire wheel covers· .......
05 Inspect for fuel, oil, coolant, and other fluid leaks ...........
06 Inspect under the vehicle for damage, rust, etc ...............
07 Visua lly check bolts and nuts on chass is and powertrain
for looseness ................................ ...................................
08 Install rubber body plugs* (stored in glove box or center
console) ...... ....... ··········· ··············· ······················· ············

0
0

FUNCTIONAL OPERATION
Apply parking brake and cycle ignition ·1G-ON"; place gear selector in reverse.
tum on lights and rear defogger. Unlock doors, release fuel door

01
02
03
04
05
06
07
08
09
10

Check dome, courtesy, map , and sun visor lights ...........
Check warning/indicator lights, gauges, and horn .........
Check windshield wipers and washers ................. .........
Check headlights, instrument lights, turn signals,
emergency flashers, and brake lights ........ .....................
Check inside/outside rear view mirror operation/
adjustment• ........ .......... ............................................... .. ..
Check cigarette lighter' and power outlets ......................
Check audio/navigation*/backup camera· systems and
set clock ....................... ..... ... .... .. . .. .. .. .. ..... .. ... .......... .... ...
Check sliding roor .. .. .. .. ... ... ..... ..... .. .... ...... ... .. ......... ..... ..
Check Rear Seat Entertainment System ope ration* ........
Install shift-lock override button cover . .... .. ... ... ............. .

DO
DO
DO
DD
OD
DO
DO
DD
OD
DO

Enter Odometer Readings
Reading Before Test.

01
02
03
04
05
06
07
08
09
10
11

OD
DO
DO
DO
DO
DO
DO
DO
DO
DO
OD

~a:

0

DO
DO
0
OD
DD
OD
0

Reading After Test.

Check cold engine operation ·· ···· ·· ·· ·········· ·········· ·· ·········· ·
Check engine operation during warm-up .. ........ ... .... .... .. .
Check engine at normal operating temperature ..............
Check automatic transmission operation .. .......................
Check brake and parking brake operation .......................
Check steering operation & off-center/vehicle pull/fl utter.
Inspect for abnormal noise and vibration .........................
Inspect for squeaks and rattles ... .. ...................................
Check front and rea r* heater and A/C operation ..............
Check cruise control operation* ......................................
Check front seat heater/ventilation operation• ..... ... . .......

DO
DO
DO
DO
DD
DD
OD
DO
DO
DD
DO

FINAL INSPECTION AND CLEANING
01 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove just before delivery to customer) .. .. ...
02 Visua lly inspect all interior parts for installation ,
damage, fit, dirt, etc . ..... .............. .. ...................................
03 Verify floor mat application and install us ing
retaining clips" ...............................................................
04 Remove Rapgard™ and clear protective bumper film* ....
05 Wash and clea n vehicle ............ .. ....... ......... .. ............ .......
06 Inspect paint fi nish for scratches, c hips, rust, dents,
damage, etc.. ..... .... ........... .. .......... .. ......... .... .. .. .... ......... ...
07 Inspect exterior body parts for proper installation,
damage, rust, etc .. .............. .. ....... ............... ........ .............
08 Place oil change sticker on inside of windshield , top
left corner ......... ...............................................................
09 Place Owner's Guide & first aid kit portfolio* in glove box
10 Perform Techstream Health Check ................................
11 Install front license plate and mounting bracket* (s ee
page 2) .. ........................ ...... .... ..... .. ........... .. .. .. .. .. ........ ....

UNDER HOOD

OD
DO
DO
DO
..... D O
OD

Check engine oil level ........ ...... .. .... ......................... .........
Check brake fluid level ...... .. .................................... ···· ··· ·
Check engine coolant level ........ .................................. .. ..
Check windshield washer fluid level ..................... ..........
Check battery state-of-charge using Digital Battery
System Analy zer (SOC Reading :
%)
06 Inspect for fuel , oil, coolant, and other fluid leaks ............

.

I;.:.ai

ROAD TEST

Start at left front door Check win dow and door lock operation (from master power
switch, if equipped) Continue around vehicle m a counterclockwise direction
checking each door and window operation. child door locks, seat bells, inferior
condition , all lights, luggage compartment contents. Finish by checking headlight
aim and continue into UNDER HOOD checks.

01
02
03
04
05

x:

0

A complete road test helps assure customer satisfaction Drive vehicle over a
variety of road surfaces and driving conditions Check for unusual noise and
driving performance

WALKAROUND INSPECTION

01 Check Smart Key System * ..... .......................................
02 Check door and door lock operation, including each
wireless remote control/theft deterrent system* ....... ...... .
03 Check window operation ... ................... ...... ..... .. ........ .....
04 Check that engine starts with all keys ...... ..... .............. ..
05 Check that child safety door locks are in normal
(unlocked) position ....... ........ .. ... ..... ............ .. ...................
06 Check seats and seat belt operation .. ........ .. .... ... ... ........
07 Check rea r defogger/rear view mirror defogger* .............
08 Check side marker, tail, backup, and license
plate lights ........... ..... .. .. ... .. ..... .. .... .............. ..... .. ...... ...... .
09 Check luggage compa rtment light* and trim appearance
10 Check jack and tool installation .. ...... .. . . . ...• .. .•.. . . ..•...•... . ..
11 Check headlight aim .......... .. .... .. ........ ... ...... .. .... ............ ..

August 201•

0

DO
DD

0
0

DO
DO
0
0

DO
D

COMMENTS:

Inspect or install when eq uipped/required.

Completion and retention of this form is required to comply with Toyota's Warranty Policy
TECHNICIAN'S SIGNATURE

SERVICE MANAGER'S SIGNATURE

NAME (PLEASE PRINT)

NAME (PLEASE PRINT)

Date

I

Dealer Name

I

Dealer Code

We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.

I

Vehicle Identification Number (Sticker)

DIC CUT FUSE INSTALLATION
To minimize battery discharge the D/C Cut Fuse has been removed
and is stored in the engine compartment Relay Block. Install the D/C
Cut Fuse and confirm all related DTCs are cleared.

1 D/C Cut Fuse Storage Location

2 Install DIC Cut Fuse Here

TIRE PRESSURE WARNING SYSTEM TPWS INITIALIZATION
Refer to the Repair Manual for the Initialization Procedure.
NOTE
• Please note the spare tire does NOT have a TPWS sensor.
• To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature,
perform a Health Check using Techstream and select the "Compensation Tire Pressure" checkbox. Compensation
pressures will be displayed on the Health Check results screen. Adjust the tire pressure when the tires are cold.

FRONT LICENSE PLATE & MOUNTING BRACKET INSTALLATION*
1. Align holes "A" of the mounting bracket with the dimples on the
front bumper cover. Mark the location of holes "B" on the front
bumper cover.
NOTE

• Holes "A" are used for installation of the mounting bracket
to the bumper cover.
• Holes "B" are used for the installation of the front license
plate to the mounting bracket.
2.

Drill 2 rel ief holes with a diameter of 11 mm (0.43 in.) at the hole
"B" marks on the front bumper cover to prevent the license plate
retaini ng bolt end from contacting cover.
NOTICE

Do NOT drill at the dimples on the front bumper cover.
3.

Install the mounting bracket to the front bumper cover by
attaching the 2 self-tapping screws into the dimples.

4.

Install the front license plate to the mounting bracket using bolts
with the following measurements:
Len gth : 15.0 - 23.0 mm (0.59 - 0.91 in.)
Diameter: 6.0 mm (0 .24 in.)
Pitch: 1.0 mm (0.04 in.)
1 Mounting Bracket
2 Dimples
3 Mark and Drill Holes

4 Self-Tapping Screws
S License Plate
6 Bolts