®TOYOTA LAND CRUISER
2015 PRE-DELIVERY SERVICE CHECK SHEET
BEFORE INSPECTION

:.: If:;t

UNDER VEHICLE (ON HOIST)

01 Install Short Pin (see pag e 2) ........................................

0

01 Remove disc brake anti -rust covers/anti-corrosion

0

wheel film* ................................................ ......................

02 Inspect tires for defects/damage and adjust spare tire

FUNCTIONAL OPERATION

air pressure .. . .. . . . .. .. . . . . . ...................................... .

03 Activate and Initialize Tire Pressure Warning System

Apply parking brake and cycle 1gnit1on ' JG-ON", place gear selector m reverse /um
on ltghls and rear defogger. Unlock doors. release fuel door

01
02
03
04
05
06
07
08
09
10
11
12

Check dome, courtesy, map, and sun visor lights· .........
Check warning/indicator lights, gauges, and horn ..........
Check windshield wipers and washers ..... .......................
Check headlights, instrument lights, turn signals,
emergency flashers , and brake lights ..........................
Check inside/outside rear view mirror operation/
adjustment ............................. ························· ... ......
Check cigarette lighter· and power outlets .
..
Check aud10/navigation'/backup camera· systems and
set clock .... ..............................................................
Install shift-lock override button cover .........................
Check sliding roof' ................................................
Check Rear Seat Entertainment system operation· .......
Check Curtain Shield Airbag Roll Sensing switch & light>
Confirm Automatic Door Lock (AOL) function .................

(TPWS) (see page 2) .. . . .. . .. . ... . . . .. .. . . ..
Install wheel covers/caps/spa re tire wheel covers' ..
Inspect for fuel , oil, coolant, and other fluid leaks .......... .
Inspect under the vehicle for damage, rust, etc.............. .
Visually check bolts and nuts on chassis and powertrain
for looseness .......... ...................................................... ..
08 Install rubber body plugs· ........................................... ... .

04
05
06
07

DO
DO
DO
DO

05
06
07
08
09
10

Reading Before Test·

0

01
02
03
04
05
06
07
08
09
10
11

DO
DO
DO

Reading After Test

Check cold engine operation ........................................ .
Check engi ne operation during warm-up ....................... .
Check engine at normal operating temperature ..............
Check automatic transmission operation .......................
Check brake and parking brake operation ...................... .
Check stee ring operation and off-center/vehicle
pull/flutter ....... ............. ............ ...................................... .
Inspect for abnormal noise and vibration ... .................... .
Inspect for squeaks and rattles ....................................... .
Check front and rear• heater and A/C operation ............ .
Check cruise control operation* .......... ................... ..... .. .
Check front seat heater/ventilation operation• ............... .

DO
DO
DO
DO
DO
DO
DO
DO
DO
DO
DO

FINAL INSPECTION AND CLEAN ING
01 Remove interior protective covers, unnecessary labels,
tags , etc. (Remove just before delivery to customer) ...... .

DO
DO
DO
DO
DO
DO
DO

02 Visually inspect all interior parts for installation,
damage, fit, dirt, etc ...................................................... .

03 Verify floor mat application and install using
retaining clips * .......................................................... .

04 Verify green light is illuminated on SOS (Safety Connect)
button* .......... ...... .................... ................... ................... .

05 Remove Rapgard™ and clear protective bumper film• ... .
06 Wash and clean vehicle ....................................... .. .. ....... .
07 Inspect paint finish for scratches, chips, rust, dents,
damage, etc........ ............... ........................ ......... ... ....... ..

Check engine oil level. ................... ................................
Check brake and power steering fluid levels ................ ...
Check engine coolant level. ....... .... .... ... ........... ................
Check windshield washer fluid level ...............................
Check battery state-of-ch arge using Digital Battery
System Analyzer (SOC Reading:
%) .....
06 Inspect for fuel , oil, coolant, and other fluid leaks ..........

CJD

Enter Odometer Reading

UNDER HOOD
01
02
03
04
05

DO
DO
0
DO
DO

A complete road /es/ helps assure customer sat1sfact1on Drive veh icle over a
vane/y of road surfaces and dnvmg cond1t1ons Check for unusual noise and
dnvmg performance

Start at left front door Check window and door lock operation (from master power
switch, if equipped) Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat bells. interior
condition, all lights. luggage compartment contents Finish by checking headlight
aim and continue mlo UNDER HOOD checks

Check Smart Key System ............................................ .
Check window operation ................................................
Check that engine starts with all keys ..........................
Check that child safety door locks are in normal
(unlocked) position ......................................................
Check seats and seat belt operation .............................
Check rear defogger/rear view mirror defogger' ............
Check side marker, tail , backup, and license plate lights
Check luggage compartment light and trim appearance .
Check jack and tool installation ... ...................................
Check headlight aim ........ .......... ....................... ...............

0

ROAD TEST

DO
DO
DD
00
DO
DO
DO
DO

WALKAROUND INSPECTION

01
02
03
04

August 201 4

08 Inspect exterior body parts for proper installation ,

DO
DO
DO
DO

damage, rust, etc ............................................................ .

09 Place oil change sticker on inside of windshield, top
10
11
12
13
14
15

DO
DO

• Inspect or install when equipped/required.

left corner ................... ....... ............................................ .
Place Owner's Guide & first aid kit portfolio* in glove box
Perform Techstream Health Check ............................... .
Install roof rack cross bars and leg covers ................
Install front license plate* (see page 2) .......................... .
Install towing wire harness connector (see page 2) ....... .
Install receiver towing hitch cap ...................................... .

0

DD
DO
DO
0
0

DO
DO
0

0

DO

0
0
0
0

Completion and retention of this form is required to comply with Toyota·s Warranty Polley

TECH NICIAN'S SIGNATURE

SERVICE MANAGER'S SIGNATURE

NAM E (PLEASE PRI NT)

NAME (PLEASE PRINT)

Date

I

Dealer Name

I

Dealer Code

We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.

1Vehicle Identification Number (Sticker)

SHORT PIN INSTALLATION
To minim ize battery discharge the Short Pin has been removed and is stored in the e ngine com partment relay block.
NOTE
• The Short Pin does NOT function as a fuse , so only install it in the position shown.
• If the vehicle is stored in the dealership for a long period of time after PDS, disconnect
the negative (-) battery term inal to prevent battery discharge. Refer to Service Bulletin
No. PG001 -06, "Battery Maintenance for In-Stock Ve hicles & Pre-Delivery," for battery
maintenance information.

1 Short Pin Storage Location
2 Install Short Pin Here

TIRE PRESSURE WARNING SYSTEM (TPWS) ACTIVATION AND INITIALIZATION
Activation Procedu re
1. Connect Techstream to DLC3.
2. Cycle the IG switch to the "IG-ON" position and check that the Low Tire Pressure Warning Light blinks for 1 minute and then
remai ns illuminated.
3 Press or remove the valve core to reduce the tire inflation pressure rapidly by 6 psi (0.4 kgf/cm2 • 40 kPA), or more, within 30 seconds
4 Using Techstream, check for DTCs (C2111-C2115). If no DTCs are stored, continue to step 5. If these DTCs are stored, repeat step 3.
NOTE
If DTCs C2111-C2114 are present after repeating step 3, lift the vehicle and rotate each tire so that the tire pressure warning
valve/sensor is at the top of the wheel well. Then repeat step 3.
5. Press the "DISP" switch o n the steering wheel and check that the tire pressures of all 5 tires are displayed on the
multi-information display.
NOTE
• The tire pressure display is NOT shown until all tire pressure warning valve/sensors are activated .
• If "Check Tire Pressure System" or "CHECKING" is displayed, repeat step 3. If step 3 is performed and the tire pressures
are still NOT displayed, lift the vehicle and rotate each tire so that the tire pressure valve/sensor is at the top of the wheel well
(i n the 12 o'clock position). The n repeat step 3.
• If the above steps are performed and the multi-information display does NOT show the tire pressure, refer to the Repair Manual.
Initialization Procedure
Refer to the Repair Manual for Initialization Procedure.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder tha n shop temperature, perform a Health
Check using Techstream and select the "Compensation Tire Pressure" checkbox. Compensation pressures w ill be displayed on the
Health Check results screen. Adjust the tire pressure when the tires are cold.

FRONT LICENSE PLATE INSTALLATION*
Front License Plate
1. Align the holes on the license pla te to the d imples on the
front bumper.
2. Using 2 self-tapping screws, insta ll the front lice nse plate on
the front bumper.

NOTICE
• Do NOT pre-drill holes into the bumper.
• Do NOT overtighten the self-tapping screws.

TOWING WIRE HARNESS INSTALLATION
The towing wire harness connector set is loaded in the vehicle at
the assembly plant.
1. Connect the frame wire harness and the towing wire
harness connector.
A . Remove the water resistant caps from the 2 frame w ire
harness connectors .
B. Connect the 2 frame wire harness con nectors and
2 towing wire harness connectors.
2. Install the towing wire harness assembly bracket to the frame
bracket with the 2 bolts.
Torque: 19.5 N* m (199 kgf>cm , 14 ft*lbf)

Use non-corroding selftapping screws w ith the
following dimensions.
Length: 16.5 - 20.0 mm
(0.65 - 0.79 in.)
Diameter: 6.0 mm (0.24 in.)

1 Self -tapping Scr ews