Technica l Service Bu lletin

~
'2:7

April 14, 2014

S-SB-0005-14

=:;c:::1on

Floor Mat Installation During PDS
Service
Category

General

Section

Pre-Delivery Service

Market

Scion Su pports ~
AS E Certifi cation: W

USA

Applicability
YEAR(S)

MODEL(S)

2015

FR-S . iO . tC . xB

ADDITIONAL INFORMATION

Introduction
2015 model year vehicles are equipped with driver's side floor mat retaining clips to secure the floor
mat in the correct position . In addition , some models may utilize retaining clips for passenger side
floor mats as well . Follow the appropriate installation procedure to attach the driver's side and
passenger's side (if applicable) floor mat to the vehicle carpet using the floor mat retaining clips
during Pre-Delivery Service (PDS) .
CAUTION
• ALWAYS verify the floor mat to ensure it is designed specifically for the model and model
year it is being installed in .
• ONLY use floor mats that can be retained using the retaining clips. All OEM Scion floor mats
are specifically designed to fit correctly and be retained using the retaining clips .
• Make sure the floor mat is properly placed on the vehicle carpet and secured with the retaining
clips. If the driver side floor mat is NOT properly placed and secured, it could slip and interfere
with the movement of the pedals during driving and may cause an accident.
• Verify the operation of the accelerator, brake, and clutch (if equipped) pedals and clearance
to the mat.
• NEVER install more than one floor mat at a time in the driver's seating position.
• If applicable, any secondary set of floor mats (based upon customer preference, such as the
all weather floor mats or other floor mats) MUST be placed in the trunk with all the packaging
material intact. Do NOT install the secondary mat on top of the primary floor mat already
installed in the driver's seating position.

Warranty Information
OP CODE

DESCRIPTION

TIME

OFP

T1

T2

NIA

Not Applicable to Warranty

-

-

-

-

© 2014 Toyota Motor Sales, USA

Page 1 of 12

S-SB-0005-14

April 14, 2014

Page 2 of 12

Floor Mat Installation During PDS

Installation Procedure: Hook Style

1. Verify that the driver and passenger side (if applicable) floor mats are for the correct model
and model year they are being installed in .
2 . Attach the driver and passenger side (if applicable) floor mats to the vehicle carpet using the
retaining clips. Secure the mat by inserting the retaining clips through the grommet holes.
Figure 1.

I

/

I

I

/

/

·cq
··· 1·..
.
. . .,_
.

:

, I....;,;,, cu,.
2

' ...
'·-

: .. :
;

.

---~ . ~/.

@.,
.

I

-, ·

'

,'

.·

.·

.
..

3

Grommets

© 2014 Toyota Motor Sales, USA

I

·.· ,:· ~ ,._.·

'....:.. ·.· ,~ . :.

Correct Installation

,- .-

.-:.

.

:·-: ,._...

I

Page 3 of 12

April 14, 2014

S-SB-0005-14

Floor Mat Installation During PDS

Installation Procedure: Hook Style (Continued)

3. Verify proper installation .
NOTE
If applicable, DO NOT remove the beige " Caution " tag from the floor mat. This should only be
removed by the customer.
Figure 2.

A

Caution I Prec~uci6n I Attention I .;.:W

A

NOTICE: THIS TAG TO BE REMOVED BY CUSTOMER ONLY.
To. avoid inlgrfete" t>'J'
. y• 'J -

© 2014 Toyota Motor Sales, USA

:~\i:-..»1 ~,., ~y:. ~

El
;UJ

o;

I

S-58-0005-14

April 14, 2014

Page 4 of 12

Floor Mat Installation During PDS

Installation Procedure: Hook Style with Locking Clip

1. Verify that the driver and passenger side (if applicable) floor mats are for the correct model
and model year they are being installed in .
2. Attach the retention clip to the floor by inserting the retention clip claws into the floor eyelet.
Figure 3.

1

Retention Clip

5

Cross-sectional Diagram

2

Front of Vehicle

A

Retention Clip Claw

3

Retention Clip Eyelet on Vehicle Floor

B

Locking Clip

4

Seat

© 2014 Toyota Motor Sales , USA

Page 5 of 12

April 14, 2014

S-SB-0005-14

Floor Mat Installation During PDS

Installation Procedure: Hook Style with Locking Clip (Continued)

3. To lock the retention clip in place, insert the
locking clip of the retention clip into the
designated hole.

Figure 4.

1

4. Align the floor mat holes with the retention clip
hooks and place the floor mat holes onto the
retention clip hooks.

I

Locking Clip

Figure 5.

1

Retention Clip Eyelet on Floor Mat

2

Retention Cl ip

3

Front

© 201 4 Toyota Motor Sales, USA

April 14, 2014

S-SB-0005-14

Page 6 of 12

Floor Mat Installation During PDS

Installation Procedure: Hook Style with Locking Clip (Continued)

5. Verify proper installation .
NOTE
If applicable, DO NOT remove the beige " Caution" tag from the floor mat. This should only be
removed by the customer.
Figure 6.

A

Caution I Precauci6n I Attention I ~W

A

NOTICE: THIS TAG TO BE REMOVED BY CUSTOMER ONLY.
l o avoid in.l9rfet ed on top of anothor
floor mat.
NEVER place the ftoor mat
in the vehicle upsidc·down ot
backwards.

PRECAUCION

A

• Use este tapete unicamente
para el !ado del conductor.
Este tapete fue diset\ado
especlficamente para usarse en
este modelo y a~o de veh lculo,
y NO DEBE usarso en ning