NUMBER

GROUP

@) HYU nDR 11

Technical Service Bulletin
SUBJECT:

14-01-036-1

CAMPAIGN

nEW THlnKlnG.
nEW POSSIBILITIES. DATE

MODEL(S)

OCTOBER 2014

ELANTRA SEDAN
(UD)

OVERHEAD CONSOLE SUNGLASS HOLDER LATCH
REPLACEMENT PROCEDURE, (SERVICE CAMPAIGN TT9)

This TSB supersedes bulletin 14-01-036 to add retail vehicles.

*IMPORTANT

.....___ _ _ _ ______, ****DEALER STOCK AND RETAIL VEHICLES*****
Dealers must perform this Campaign on all affected vehicles prior to customer retail delivery and
whenever an affected vehicle is in the shop for any maintenance or repair.
When a vehicle arrives at the Service Department, access Hyundai Motor America 's "Warranty
Vehicle Information" screen via WEBDCS to identify open Campaigns .
Description: In some Elantra vehicles the sunglass holder in the overhead console may open
unintentionally while driving over bumpy roads . This bulletin describes the procedure to replace the
sunglass holder latch to correct this condition .
Additionally, vehicles with a sunroof motor may lose sunroof home position during the replacement
part process . This bulletin describes the procedure to reset the sunroof motor (if equipped).

Applicable Vehicles: Certain 2014 and 2015 Elantra (UD - American built- VINs starting with
5NPDH ***) vehicles.
Parts Information:
Part Name

Before

SUNGLASS
CASE LATCH

After

Qty.

92826-3XOOOQQH

1

UD
Without Sunroof

40CA06R1

SUNGLASS CASE
LATCH REPLACEMENT

0.2 M/H

UD
With Sunroof

40CA06R2

SUNGLASS CASE
LATCH REPLACEMENT
AND SUNROOF RESET

0.3 M/H

NOTE: Submit Claim on Campaign Claim Entry Screen
Circulate To : General Manager, Service Manager, Parts Manager, Warranty Manager, Service
Advisors , Technicians , Body Shop Manager, Fleet Repair

SUBJECT:

OVERHEAD CONSOLE SUNGLASS HOLDER LATCH REPLACEMENT (SERVICE CAMPAIGN TI9)

Service Procedure:
SUNGLASS HOLDER LATCH REPLACEMENT
1.

Open the sunglass holder (A).

2.

Remove the two screws (8) .

3.

Pull down the overhead console (C) to
separate it from the headliner.

TSB #: 14-01-036-1

Page 2 of 8

SUBJECT:

4a .

OVERHEAD CONSOLE SUNGLASS HOLDER LATCH REPLACEMENT (SERVICE CAMPAIGN TI9)

Disconnect the connector (01 ).

NOTICE
Picture to the right shows a nonsunroof model.
Remove the overhead console (C) from the
vehicle .

4b .

For a sunroof-equipped model , also
disconnect the connector (02).

NOTICE
A small flathead screwdriver may be
required to remove connector (02).
Remove the overhead console (C) from the
vehicle .

NOTICE
For sunroof-equipped models, a
sunroof reset procedure must be
performed. After latch replacement is
complete, refer to page 6 for sunroof
motor reset procedure.

TSB # : 14-01-036-1

Page 3 of 8

SUBJECT:

5.

OVERHEAD CONSOLE SUNGLASS HOLDER LATCH REPLACEMENT (SERVICE CAMPAIGN TI9)

The sunglass holder latch (E) is located at
the front left side of the overhead console.

NOTICE
There is no visible difference between
the old and the new part. Be careful to
not re-install the old part.

6.

Push the back side of the holder latch (E)
with a driver (F) to remove the holder latch
from the overhead console.

CAUTION
Set the console on a clean surface
that will not get damaged nor cause
damage to the console during removal
of the holder latch.

TSB # : 14-01-036-1

Page 4 of 8

SUBJECT:

7.

OVERHEAD CONSOLE SUNGLASS HOLDER LATCH REPLACEMENT (SERVICE CAMPAIGN TI9)

Insert the new holder latch (E*) with needle
nose pliers (G) in the orientation shown.

CAUTION
Before installation, compare the
orientation of the holder latch (E*) with
the picture on the right. The slotted
side should be facing away from your
view.

8.

Push in the new holder latch (E*) in the

direction of the arrow. You should hear and
feel a confirmation "click ."

9.

Confirm the correct orientation of the holder
latch installation by comparing it to the
pictures to the right.
Close and open the sunglasses holder to
confirm that it operates normally.

0 =

Correct

10.

X

=Incorrect

Reinstall the overhead console by reinstalling the parts in reverse order of removal.

TSB #: 14-01-036-1

Page 5 of 8

SUBJECT:

OVERHEAD CONSOLE SUNGLASS HOLDER LATCH REPLACEMENT (SERVICE CAMPAIGN TI9)

SUNROOF RESET (FOR SUNROOF-EQUIPPED VEHICLES ONLY)
1.

Start the sunroof reset procedure under the
following conditions :
Sunshade open
Sunroof glass closed

•
•
•••••••·- --i
2.

Turn the ignition key (A) to the "ON " position.

Key start

Push-button start

For push-button start, press button (A)
2 times for "ON " without depressing the brake
pedal. (Do not start the engine.)

3.

Push and hold the sunroof glass switch (B)
forward in the direction of close for 10
seconds.

TSB # : 14-01-036-1

Page 6 of 8

SUBJECT:

OVERHEAD CONSOLE SUNGLASS HOLDER LATCH REPLACEMENT (SERVICE CAMPAIGN TI9)

4.

Keep holding the switch until the sunroof
glass automatically tilts up and then moves
up/down sl ightly.

5.

After the sunroof glass moves in Step 4,
release the sunroof switch (B) .

6.

Within 3 seconds of releasing the switch (B) ,
push and hold the switch (B) forward in the
direction of close again until the sunroof glass
moves as follows:
Tilt down -7 Slide open -7 Slide close

A

CAUTION

DO NOT release the control lever (B)
until the operation is completed.
If you release the control lever (B)
during the operation, you must restart
the sunroof resetting procedure.

TSB#: 14-01-036-1

Page 7 of 8

SUBJECT:

7.

OVERHEAD CONSOLE SUNGLASS HOLDER LATCH REPLACEMENT (SERVICE CAMPAIGN TI9)

Confirmation :
a. Push the sunroof glass switch (B) rearward
past the detent to open the glass completely.
b. Push the sunroof glass switch (B) forward
past the detent to close the glass completely.

A

CAUTION

If the sunroof glass does not open or
close fully when pressing the switch
one time past the detent, repeat the
sunroof motor reset procedure.

TSB #: 14-01-036-1

Page 8 of 8