GROUP

@) HYUnDRI I

NUMBER

AUTOMATIC
TRANSMISSION

nEWTHlnKlnG.
nEW POSSIBILITIES.

12-AT-025

DATE

Technical Service Bulletin

MODEL
GENESIS SEDAN (BH)
GENESIS COUPE (BK)

OCTOBER 2012

ATM OIL TEMPERATURE SENSOR
OTC P0711, P0712 & P0713

SUBJECT:

This TSB supersedes TSB 11-AT-016-1 to add Genesis Coupe.
Description: The Genesis Sedan and Genesis Coupe are equipped with an 8-speed
transmission. Do not replace the transmission for the OTC listed below. Instead , follow the repair
procedure and replace the related part.
Applicable Vehicles:
2012- Genesis Sedan 3.8L/4.6L/5 .0L
2013- Genesis Coupe 2.0L/3.8L.
OTC LIST:
I

DTC

DESCRIPTION

P0711

Transmission Fluid Temperature Sensor 'A' Circuit

P0712

Transmission Fluid Temperature Sensor 'A' Circuit Low

P0713

Transmission Fluid Temperature Sensor 'A' Circuit High

PARTS INFORMATION:
MODEL

PNC

PART NUMBER

DESCRIPTION

2012- GENESIS SEDAN 3.8L

46305C

46305-4F100

E-Module

2012- GENESIS 4.6L/5.0L

46305C

46305-4E100

E-Module

2013- GENESIS COUPE 2.0L/3.8L

46305C

46305-4F1 00

E-Module

WARRANTY INFORMATION:
OP CODE

OPERATION

OP TIME

CAUSAL PART

45600ROO

Replace valve body assy.

1.4

45600RQO

GDS Operation

0.3

See Parts
Information

NATURE
CODE

CAUSE
CODE

N27

C15

SERVICE PROCEDURE:

Circulate To : Service Manager, Warranty Manager, Service Advisors , Technicians , Fleet Repair

SUBJECT:

ATM OIL TEMPERATURE SENSOR OTC P0711, P0712 & P0713

1.

Using a GOS, check for OTC in the "Automatic Transaxle" menu. Record the OTC and
description . Delete the OTC .

2.

From the GOS , select the following parameters. Drive the vehicle and monitor the sensors.
• Vehicle and AfT menu.
• Current Data menu
• "Oil temperature sensor".

3.
Preparation

f1@··§·1*M+@li!AMBmlllmm 1 ;$ 1 ~ 1 • 1 {@ 1 mlEllEZl:J
Value ! Unit

Senso r Name

6::1 Oil Temperature Sensor

29

0 Engine RPM

0

·c

950 RPM

3 MPH
3.5 %
5.9 %

Vehlde Speed

0 Acce leretor Pedal Position Sens or
D fThrottle Positio n Sensor Angle
D Input Speed(PG..AJ

679 RPM

0

Output Speed(PG-8)

D
O
D
D
0
O
Cl
D
D
0
D

Gear Ratio

178 RPM
3.7 -

Torque Converter Outch Slip

274 RPM

Ma in Rela y Voltage
Engine Torque
Shift Leve r Swilch
Current Gear
Next Ge ar Position
Torque Conve rter Clutch Control State
Hold Switch
Idle Switch

143

v

9.0 .,.
D -

1 1 OFF Hot Supporte d
Hol Supported
Hot Supporte d
Hot Supported
OFF
OFF

Kick Down Switch

D 00 Switch(O/D)

0 Brake Switch
[] Auto Crufse Switch

-

-

D

n

D
0
D

Sports Mode Seled

Hot Supported OFF -

Sports Mode Up Switch
Sports Mode Down Switch
Reverse lama Reh1v Outaut

Not Suoootte d -

n

Switch (4WD Only)

Case Anaf'f' is

OTC

OFF OFF -

Actuation
Test

FlightRtoord

~
OVOM

~1~
.
SlmulatiOn
Oscillostope
Test

I

4.

If the sensors show:
• Continuous and changing output while driving from a cold start, the wiring currently has no
open/short circuits . Go to Step 6 .
• "No continuous and changing output, go to Step 5.

5.

Visually check the wiring harness between the PCM and transmission for a damaged wire or
connector. Check for a short circuit to ground .
• If damage exists , repair or replace the ECM control harness and drive the vehicle to confirm
the repair.
• If not, go to Step 6.

6.

Disconnect the negative battery terminal.

TSB #: 12-AT-025

Page 2 of 6

SUBJECT:
7.

ATM OIL TEMPERATURE SENSOR OTC P0711, P0712 & P0713

Lift the vehicle on a hoist.
Press the tab in the center of the latch and
push the latch upward.
Push the connector up to disconnect the
connector.

8.

Use an 8mm or 5/16" hex socket and remove
the drain plug and drain the ATF .
Remove the 14 bolts that secure the oil pan
and remove the pan.
Torque: 6-7 lb.ft (0.9-1.0 kgf.m)

9.

Remove the 10 bolts that secure the valve
body to the case and remove the valve body.
Note the location of the 3 black long bolts.

TSB #: 12-AT-025

Page 3 of 6

SUBJECT:

ATM OIL TEMPERATURE SENSOR DTC P071 l, P0712 & P0713

10. Remove 8 bolts and remove the E-Module .
Install the new E-Module and torque the bolts
to specification.
Torque: 6-7 lb.ft (0.9-1 .0 kgf.m)

ASSEMBLY

11 . Confirm that 5 a-rings are seated in the case.

12. Align the manual valve to the shift lever and
install the valve body.

TSB #: 12-AT-025

Page 4 of 6

SUBJECT:

ATM OIL TEMPERATURE SENSOR OTC P0711 , P0712 & P0713

13. Install 10 bolts and torque to specification.
Install the 3 black bolts in the correct location.
Torque: 7.2-8. 7 lb.ft (1.0-1.2 kgf.m)

14.

Reconnect the harness connector and pull the latch down until it clicks (See Step 7).

15.

Install the oil pan and torque the bolts to specification
Torque: 6-7 lb.ft (0.9-1.0 kgf.m)

16. Reinstall the negative battery terminal.
17. Use an 8mm or 5/16" hex socket and remove
the fill plug and washer.
Shift into Park and lift the vehicle on a hoist.
Use a fluid pump or suction gun to add
approximately 4 quarts of SPH-IV-RR ATF
through the fill plug.

*NOTE
Use only SPH-IV-RR ATF, P/N 0023219052.

TSB #: 12-AT-025

Page 5 of 6

SUBJECT:

ATM OIL TEMPERATURE SENSOR DTC P071 l, P0712 & P0713

18. Remove the overflow plug.
Start the engine.
Add approximately 4-5 additional quarts of
SPH-IV-RR ATF through the fill plug until the
ATF flows out.
Reinstall the fill plug and washer.
Torque: 25-32 lb-ft (3.5-4.5 kgf.m)
Reinstall the overflow plug.
Torque: 16-18 lb-ft (2.3-2 .5 kgf.m)

19. Attach a GOS and select vehicle, Alf menu , Current Data and "Oil Temperature Sensor".
20.

Drive the vehicle until the ATF is at the low end of the range of 122-140°F (50-60 °C).

21.

Move the shift lever to "P" and leave the
engine idling . Raise the vehicle on a hoist.
Remove the overflow plug. The ATF level is
correct when the A TF flows out in a steady,
thin stream.

ATF TEMPERATURE= 122-140°F (50-60°C)
SHIFT LEVER IN " P" AND ENGINE RUNNING

22. Attach a GOS and delete any OTC.
23.

Drive the vehicle to confirm the proper operation of the transmission.

TSB #: 12-AT-025

Page 6 of 6