SERVICE BULLETIN

SB-10056639-2441

Bulletin Type...…:

C

Bulletin No…..…:

TS-C69

Bulletin Name..…:

Relocating the secondary fuel filter

Bulletin Ref.No…:

700002361

Release Date……:

10.07.2014

Expiry Date……..:

10.07.2015

Vehicle Model….:

TS-30

Flat Rate Code….:

TS-C69

Flat Rate Time….:

60’

SUBJECT : Relocating the secondary fuel filter

Bulletin Responsible……………….: Fatih Nasirci
Published by & Approved by... : Süleyman Uğurses

SUMMARY : This bulletin gives instruction for relocating
the secondary fuel filter to improve the serviceability of
TS30 vehicles.

Welding on the Chassis
• Always disconnect the batteries (starting with the negative lead).
• Disconnect the connectors of electrical and electronic equipment (electronic control units, sensors and actuators) if they are less than
20 inches away from the chassis part to be welded or the earth terminal of the welding equipment.
• The earth terminal should never be attached to vehicle components such as engine, axles and springs. Arcing on these parts is not
permitted, because of the risk of damage to bearings, springs, etc.
• The earth terminal must make good contact and be placed as close as possible to the part to be welded.
• Plastic pipes, rubber parts and parabolic springs should be well protected against welding spatter and temperatures
higher than 70°.
• The contact switch must not be in the accessory or contact position. The contact key should be removed.
• Reconnect in reversed order of disconnecting. Ensure that a good earth connection is made between chassis, engine
and cab.

TS-C69 1 / 11

SERVICE BULLETIN
Service bulletin expiry dates differ according to service
bulletin type.

Definitions

U-Type : Application period of this bulletin is 12
months after the date of issue.U type bulletin is used
for updates that need to be performed upon
customer complaints.

Release Date: As of this date the bulletin is released
and available on E-Doc. Modification parts can be
ordered. The time period between the release date
and the effective date may vary according to the
procurement lead time.
Effective Date: As of this date specified amount of the
total modification parts will be available on Spare
Parts Stock. Modification parts can be ordered and the
application can be performed. ( except noncompliance and safety related campaigns, i.e. S-Type
Bulletin)

• C-Type: Application period of this bulletin is 12
months after the date of issue. C type bulletin is
generally used for supplying technical instructions or
other type of information to service network.

Part Order Deadline: Last order date for modification
parts. The part orders which will be placed after this
date should be approved by Regional Coordinator.
Expiry Date: Expiration date for the application.
Bulletin Types
• S- Type: Application period of this bulletin is
18 months after the date of issue. S type bulletin is
used for Recall Campaigns.
• M-Type: Application period of this bulletin is 12

months after the date of issue. M type bulletin is used
for updates that should be implemented without
waiting for customer complaints.

TS-C69 2 / 11

SERVICE BULLETIN
Parts List
INSTALLED PARTS LIST
No

PART NO

PART NAME

Qty.

UNIT

MEASURE

1

HD155149Y

BRACKET

1

Piece

2

9302-636Y

L-PLATE

2

Piece

3

9326-3133Y

BRACKET

1

Piece

UNIT

MEASURE

EXCLUDED PARTS LIST
No

PART NO

PART NAME

Qty.

TS-C69 3 / 11

SERVICE BULLETIN
Technical Instructions
1. Remove the battery cables

2. Open the door of DEF tank.

Picture 2

3. Mark the center of the hole as identified in
the drawing given in below. Drill a hole which is
13 mm( 0,511") diameter.

66,5 mm=2,6 ''
89 mm=3,5 ''

TS-C69 4 / 11

SERVICE BULLETIN

4. Adhere the part of HD155149Y on the
center of hole

Picture 4

5. Measure 30 mm(1,18") from the edge
and adhere the L-Plate has part number
9302-636Y

Picture 5

TS-C69 5 / 11

SERVICE BULLETIN

6. Measure 180 mm(7,1") from the edge and
adhere the second L-Plate has part number
9302-636Y

7. Measure 287 mm(11,3") from the bottom
and 334 mm(13,15") from the rearwall, cut a
hole has a dimension as 102 mm x 10 mm
(4"X0,4")

TS-C69 6 / 11

SERVICE BULLETIN

8. Measure 50 mm (2") from the panel and
adhere the bracket (9326-3133) on to the
profile behind the panel by welding. Fill the
edges of bracket with sealer .

TS-C69 7 / 11

SERVICE BULLETIN

9. Remove the fuel filter from the existing location

10. Install the fuel filter to the new location.

TS-C69 8 / 11

SERVICE BULLETIN

11.Measure 135 mm(5,31") from the edge and 415
mm(16,33") from the bottom. Drill a hole has a
diameter of 50 mm(2") for the passage of fuel
hoses

TS-C69 9 / 11

SERVICE BULLETIN

TS-C69 10 / 11

SERVICE BULLETIN
Flat Rate Break Down
Breakdown Steps of Application
Preparetion for tools
Dismounting of fuel filter
Mounting brackets and fuel filter
TOTAL

Duration (min)
5'
15'
40'
60

TS-C69 11 / 11