SB-10056480-2670
Reference:

Date:

NTB14-092

October 7, 2014

VOLUNTARY EMISSION RECALL CAMPAIGN
2008 – 2010 ROGUE SULEV SPECIFICATION
ECM REPROGRAM
CAMPAIGN ID #:

R1408

APPLIED VEHICLES: 2008 - 2010 Rogue (S35) SULEV specification
Check Service COMM to confirm campaign eligibility.

INTRODUCTION
Nissan is conducting a Voluntary Emission Recall Campaign on certain Model Year 2008 –
2010 Rogue vehicles equipped with SULEV (Super Ultra Low Emissions Vehicle)
specification. The ECM (Engine Control Module) will be reprogramed. This service will be
performed at no charge for parts or labor.

IDENTIFICATION NUMBER
Nissan has assigned identification number R1408 to this campaign. This number must
appear on all communications and documentation of any nature dealing with this campaign.

DEALER RESPONSIBILITY
It is the dealer’s responsibility to check Service Comm for the campaign status on each
vehicle falling within the range of this voluntary emissions recall which for any reason
enters the service department. This includes vehicles purchased from private parties or
presented by transient (tourist) owners and vehicles in a dealer’s inventory.

Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.

1/13

IMPORTANT
Attention California Dealers: California law prohibits owners from renewing their
California registration if emissions related recall work has not been performed. California
dealers are now required to issue a proof of correction certificate to vehicle owners upon
completion of emission related recall work. Please fill out one of the campaign completion
forms for each owner that has this campaign performed. Instruct owners to keep this
certificate unless they are requested to mail it to the DMV. A sample of the form is shown
below.

NOTE: These forms are available as follows:
Order online: Log into NNAnet.com, select Workspace, under Dealer Operations
select Dealer Materials Ordering. Order item CAEMRC-5-13.
For additional information: Call IMS Group 2 Communications at 1-800-247-5321.

l

T

ehicle Identification Number

CAEMRC-5-13

2/13

NTB14-092

REPAIR OVERVIEW
Use Service Comm (campaign ID # R1408) to confirm
the vehicle you are working on is affected by this campaign

Use Service Comm:
Has campaign ID # P9249 / NTB09-126 been completed?
NO

YES

Complete campaign
P9249 / NTB09-126
first.

NOTE: You may need to perform
ECM reprogramming twice. Once for
campaign P9249 / NTB09-126, and
then once again for this campaign.

Perform campaign /
Service Procedure in
this bulletin.

3/13

NTB14-092

SERVICE PROCEDURE
NOTE:


Most instructions for reprogramming with CONSULT-III plus (C-III plus) are
displayed on the CONSULT PC screen.



If you are not familiar with the reprogramming procedure, click here. This will link
you to the "CONSULT- III plus (C-III plus) Reprogramming" general procedure.



Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume
Learn (IAVL) conditions:

 Engine coolant temperature: 70 -100°C
(158 - 212°F)
 Battery voltage: More than 12.9V (At idle)
 Transmission: Warmed up
Figure A


After reprogramming is complete, you will be required to perform Throttle Valve
Closed Position, Idle Air Volume Learn, Accelerator Closed Position, and DTC
erase.

CAUTION:


Connect the GR8 to the vehicle 12 volt battery and set to ECM power supply mode.
If the vehicle battery voltage drops below 12.0V or rises above 15.5V during reprogramming,
the ECM may be damaged.



Be sure to turn OFF all vehicle electrical loads.
If a vehicle electrical load remains ON, the ECM may be damaged.



Be sure to connect the AC Adapter.
If the CONSULT PC battery voltage drops during reprogramming, the process
will be interrupted and the ECM may be damaged.



Turn off all external Bluetooth® devices (e.g., cell phones, printers, etc.) within
range of the CONSULT PC and the VI. If Bluetooth® signal waves are within
range of the CONSULT PC during reprogramming, reprogramming may be
interrupted and the ECM may be damaged.

4/13

NTB14-092

1. Use Service Comm: Is the vehicle you are working on affected by campaign
ID # P9249 / NTB09-126?
YES – make sure campaign ID # P9249 / NTB09-126 is completed first.
NOTE: Campaign P9249 / NTB09-126 must be completed before doing this
campaign.
NO – Continue with this Service Procedure.
2. Connect the CONSULT PC to the vehicle to begin the reprogramming procedure.

3. Open C-III plus and wait for the plus VI to be recognized.


Serial number will display when the plus VI is recognized.

4. Select Re/programming, Configuration.

VI is
recognized

Step
4

Figure 1

5. Follow the on-screen instructions and navigate the C-III plus to the screen shown in
Figure 2 on the next page.

5/13

NTB14-092

6. When you get to the screen shown in Figure 2, confirm this bulletin applies as follows.
A. Find the ECM Part Number and write it on the repair order.
NOTE: This is the current ECM Part Number (P/N).

xxxxxxxxxxxxxx

6A: Current ECM P/N
xxxx
xxxxxxxxxxxxxx
xxxxxxxxxxxxxx

Figure 2
B. Compare the P/N you wrote down to the numbers in the Current ECM Part Number
column in Table A below.


If there is a match, continue with the reprogramming procedure.



If there is not a match:
a. Make sure campaign P9249 / NTB09-126 has been completed.
NOTE: campaign P9249 / NTB09-126 must be completed before doing this
campaign.
b. After completing campaign P9249 / NTB09-126, recheck for a P/N match for
this campaign, in Table A below.
NOTE: You may need to perform ECM reprogramming twice. Once for
campaign P9249 / NTB09-126, and then once for this campaign.
c. If there is still no P/N match, correct reprogramming has already been done,
close this campaign using op-code R14081.

Table A
Current ECM P/N: – 23710 JM02C,
JM03D,
JM72C,
JM73C,

JM02D
JM03E
JM72D
JM73D

CZ40A
CZ41A
CZ32A, CZ32B, CZ32C, CZ32D, CZ32E
CZ33A, CZ33B, CZ33C, CZ33D, CZ33E

6/13

NTB14-092

7. Follow the on-screen instructions to navigate C-III plus and reprogram the ECM.

NOTE:


In some cases, more than one new P/N for reprogramming is available.
 In that case, the screen in Figure 3 displays.
 Select and use the reprogramming option that does not have the message
“Caution! Use ONLY with NTBXX-XXX”.



If you get this screen and it is blank (no reprogramming listed), it means there is no
reprogramming available for this vehicle.

xxxxx-xxxxx

xxxxx-xxxxx

xxxxxxxxxxxxxxxxxxxxxx

xxxxx-xxxxx

xxxxx-xxxxx

xxxxxxxxxxxxxxxxxxxxxx

Figure 3

7/13

NTB14-092

8. When the screen in Figure 4 displays, reprogramming is complete.

NOTE: If the screen in Figure 4 does not display (reprogramming does not complete),
refer to the information on the next page.

9. Disconnect the battery charger from the vehicle.

10. Select Next.

Step
10

Figure 4

NOTE:


In the next steps (page 10), you will perform Throttle Valve Closed Position, Idle Air
Volume Learn, Accelerator Closed Position, and DTC erase.



These operations are required before C-III plus will provide the final reprogramming
confirmation report.

8/13

NTB14-092

ECM Recovery
Do not disconnect plus VI or shut down C-III plus if reprogramming does not
complete.
If reprogramming does not complete and the “!?” icon displays as shown in
Figure 5:


Check battery voltage
(12.0–15.5 V).



Ignition is ON, engine OFF.



External Bluetooth® devices
are OFF.



All electrical loads are OFF.



Select retry and follow the
on screen instructions.



“Retry” may not go through
on first attempt and can be
selected more than once.

Figure 5

If reprogramming does not complete and the “X” icon displays as shown in
Figure 6:


Check battery voltage
(12.0 – 15.5 V).



CONSULT A/C adapter is
plugged in.



Ignition is ON, engine OFF.



Transmission is in Park.



All C-III plus / VI cables are
securely connected.



All C-III plus updates are
installed.



Select Home, and restart
the reprogram procedure
from the beginning.

Figure 6

9/13

NTB14-092

11. Follow the on-screen instructions to perform the following:


Throttle Valve Closed Position



Idle Air Volume Learn (IAVL)

NOTE:
o Listed below are common conditions required for IAVL to complete.
o If IAVL does not complete within a few minutes, a condition may be out of
range.
o Refer to the appropriate Electronic Service Manual (ESM) for specific
conditions required for the vehicle you are working on.








Engine coolant temperature: 70 -100° C (158 - 212°F)
Battery voltage: More than 12.9V (At idle)
Selector lever: P or N
Electric load switch: OFF (Air conditioner, headlamp, rear window defogger)
Steering wheel: Neutral (Straight-ahead position)
Vehicle speed: Stopped
Transmission: Warmed up



Accelerator Pedal Close Position Learning



Erase DTCs

Continue to the next page.

10/13

NTB14-092

12. When the entire reprogramming process is complete, the screen in Figure 7 will display.
13. Verify the before and after part numbers are different.
14. Print a copy of this screen (Figure 7) and attach it to the repair order for warranty
documentation.
15. Select Confirm.

xxxxx

Step
13

xxxxx
xxxxxxx
xxxxxxxxxxxxxxxxx

Step
14

Step
15

Figure 7
16. Close C-III plus.
17. Turn the ignition OFF.
18. Disconnect the plus VI from the vehicle.
19. Make sure the vehicle operates correctly and the MIL is OFF.


If the MIL comes ON, go back to ASIST for further diagnostic information.



Diagnosis and repairs beyond ECM reprogramming are not covered by this bulletin.

11/13

NTB14-092

CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
CAMPAIGN (“CM”) I.D.
R1408

DESCRIPTION

OP CODE

FRT

Reprogram ECM

R14080

0.5 hrs

If campaign is open in Service Comm but reprogram already performed
CAMPAIGN (“CM”) I.D.
R1408

DESCRIPTION

OP CODE

FRT

ECM reprogram is not needed

R14081

0.3 hrs.

12/13

NTB14-092

OWNER’S LETTER
For State of Califronia Owner’s
Dear Nissan Rogue Owner:
Nissan has discovered that your vehicle may be equipped with an improperly calibrated Engine Control
Module (ECM) that, if not repaired, could eventually cause exhaust gas emissions to exceed California
standards. This incident has no effect on fuel consumption, drivability, performance, or safety.
You should also be aware that if your vehicle is not repaired it may fail a Smog Check test in those areas of
California where such testing is required under state law. The California Department of Motor Vehicles, in
conjunction with the Air Resources Board, has implemented the Registration Renewal/Recall Tie-In Program,
which requires affected vehicles registered in California to complete the recall before the DMV will issue a
registration or renewal.
What Nissan Will Do
To correct this condition, Nissan is conducting an Emission Recall Campaign to reprogram the Engine Control
Module in your vehicle. This free reprogramming service should take about one hour to complete, but your
Nissan dealer may require your vehicle for a longer period of time based upon their work schedule. To
ensure the least inconvenience for you, it is important that you have an appointment before bringing
your vehicle to the dealer for service.
Your vehicle is eligible for this free service even if non-original parts were used for previous service and
repairs, or if the service was performed by a repair facility other than a Nissan dealer.
What You Should Do
Contact your Nissan dealer at your convenience in order to arrange an appointment to have your vehicle
repaired beginning on October 13, 2014. Please bring this notice with you when you arrive for your service
appointment. Instructions have been sent to your Nissan dealer.
If the retailer fails to, or is unable to complete this service free of charge, you may contact the Nissan
Consumer Affairs Department at the toll free number 1-800-NISSAN1 (1-800-647-7261) or by mail at:
Nissan North America, Inc.
P.O. Box 685003
Franklin, TN 37068-5003
Thank you for your cooperation. We are very sorry for any inconvenience this may cause you.

For Non-Califronia Owner’s
Dear Nissan Rogue Owner:
Nissan has discovered that your vehicle may be equipped with an improperly calibrated Engine Control
Module (ECM) that, if not repaired, could eventually cause exhaust gas emissions to exceed Federal
standards. This incident has no effect on fuel consumption, drivability, performance, or safety.
What Nissan Will Do
To correct this condition, Nissan is conducting an Emission Recall Campaign to reprogram the Engine Control
Module in your vehicle. This free reprogramming service should take about one hour to complete, but your
Nissan dealer may require your vehicle for a longer period of time based upon their work schedule. To
ensure the least inconvenience for you, it is important that you have an appointment before bringing
your vehicle to the dealer for service.
What You Should Do
Contact your Nissan dealer at your convenience in order to arrange an appointment to have your vehicle
repaired. Please bring this notice with you when you arrive for your service appointment. Instructions have
been sent to your Nissan dealer.
If the retailer fails to, or is unable to complete this service free of charge, you may contact the Nissan
Consumer Affairs Department at the toll free number 1-800-NISSAN1 (1-800-647-7261) or by mail at:
Nissan North America, Inc.
P.O. Box 685003
Franklin, TN 37068-5003
Thank you for your cooperation. We are indeed sorry for any inconvenience this may cause you.
13/13

NTB14-092