SB-10054588-5461

Service Bulletin
Applies To:

13-104
December 21, 2013

2013 Accord – ALL

Low Tire Pressure Indicator Is On With No DTC or DTC 151-11 in
VSA System
SYMPTOM
The low tire pressure indicator is on with no DTC or
DTC 151-11 (low tire pressure threshold refinement) in
the VSA system and the tire pressures were properly
set to the driver’s door jamb label.
POSSIBLE CAUSE
Software update is needed for different driving
conditions and wheel size.
CORRECTIVE ACTION
Update the VSA modulator control unit.
SOFTWARE INFORMATION
NOTE: Unnecessary or incorrect repairs resulting from
a failure to update the MVCI or HDS are not covered
under warranty.
MVCI Control Module (CM) Update:
Application (FW) Version: 3.01.37 or later
Database Update: 15 November 2013 or later
HDS Software Version:
3.012.015 or later
Before beginning the repair, make sure that both
the HDS and the MVCI are updated as listed above.
Do only the update listed in this service bulletin.
Check that the MVCI indicates the applicable program
ID listed below (or a later program ID) as the
Recommended Update when the update begins.
If the MVCI displays This vehicle does not need an
update at this time during the update, check the MVCI
Control Module update application is correct as shown
above. If the software is correct, the MVCI software
has been updated. If the software is not correct, update
both the MVCI and the HDS software.

2013 Accord 2-Door
PROGRAM ID
(or later)

PROGRAM P/N
(or later)

L4, CVT, EX, LX
with 17wheels

3LA030

57114-T3L-A03

L4, M/T, EX, LX
with 17wheels

3LA530

57114-T3L-A53

V6, A/T, EX
with 18wheels

3MA030

57114-T3M-A03

V6, M/T, EX
with 18wheels

3MA530

57114-T3M-A53

PROGRAM ID
(or later)

PROGRAM P/N
(or later)

L4, CVT, LX
with 16wheels

2FA040

57114-T2F-A04

L4, CVT, EX
with 17wheels

2FA040

57114-T2F-A04

L4, CVT, Sport
with 18wheels

2FA040

57114-T2F-A04

L4, M/T, LX
with 16wheels

2FA340

57114-T2F-A34

L4, M/T, EX
with 17wheels

2FA340

57114-T2F-A34

L4, M/T, Sport
with 18wheels

2FA340

57114-T2F-A34

V6, A/T, EX
with 17wheels

2GA040

57114-T2G-A04

V6, A/T, Touring
with 17wheels

2GA740

57114-T2G-A74

TRIM/WHEEL SIZE

2013 Accord 4-Door
TRIM/WHEEL SIZE

For more information about updating the HDS, the
MVCI, and vehicle systems, refer to Service Bulletin
01-023, Updating Control Units/Modules.

 2013 American Honda Motor Co., Inc. – All Rights Reserved

ATB 50072 (1312)

1 of 3

CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment,
and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume
this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an
authorized Honda automobile dealer.

WARRANTY CLAIM INFORMATION
The normal warranty applies.
Operation Number:
Flat Rate Time:
Failed Part:
Defect Code:
Symptom Code:
Skill Level:

4135A2
0.3 hour
P/N 57110-T2F-A23
03217
03215
Repair Technician

10. Scroll down and select “Running change, IF

YES, Press ENTER”. Press ENTER again to
start reprogramming.

CM Update Mode
Running change
If YES, Press ENTER.
If NO, Press ESC.

REPAIR PROCEDURE
1. Connect a fully charged jumper battery to the

vehicle and leave it connected during the
entire update procedure to maintain a steady
voltage.
2. Apply the parking brake and make sure the

headlights are in the OFF position.
3. Turn the ignition switch to ON (II), or press the

engine start/stop button to select the ON
mode, and turn all accessories off.
4. Connect the MVCI to the vehicle.
5. Press the ENTER button on the MVCI to see

the User Config menu. Select CM Update
Mode, then press ENTER.
6. Select Reprogramming, then press ENTER.
7. The CM Update Mode software screen

appears. Press ENTER to continue.
NOTE: The FW VER must be 3.01.37 or later and
Database Update must be 15 November 2013 or
later.
8. The Select System screen appears. Select

ABS/VSA, then press ENTER.
NOTE: If the VSA update is the only available
update, it will automatically go to the VSA
selections.

Select System
PGM-FI (Diesel)
ABS/VSA

11. Set the cold tire pressures according to the tire

label listed on the doorjamb while the MVCI
updates the vehicle.
12. Once the update is complete, follow the on-

screen prompts to turn the ignition OFF, then
ON again when indicated.
NOTE: If an error occurs during the updating
procedure, keep the ignition ON; press ENTER to
display the error code. If the error code is A, restart
the update.
If it’s not 5A, refer to the CM Update Error Code
Table in the MVCI User Guide for more information
about the error code and its solutions.
13. Press ENTER when the MVCI displays the

message “VSA Sensor Neutral Position
Memorization is required after the completion
of the update, scroll down and press ENTER.
Go to VSA Sensor Neutral Position
Memorization Procedure.
VSA Sensor Neutral Position Memorization
Procedure
1. Connect the HDS laptop to the MVCI.
2. Turn on the HDS, and make sure the HDS software
version is 3.012.015 or later.
• Select Honda Systems.
• Select ABS/TCS/VSA.
• Select Adjustment.
• Select All Sensors, then follow the on-screen
prompts.
3. Once completed, exit the VSA system, turn the
ignition OFF, then ON again. Go to EPS Steering
Angle Sensor Neutral Position Clear Procedure.

9. For program ID and program part number, see
the chart on the front page.

2 of 3

13-104

EPS Steering Angle Sensor Neutral Position Clear
Procedure
1. Go to EPS on the HDS.
• Select Adjustment.
• Select Steering Angle Sensor Value Clear.
• Follow the on-screen prompts.
2. Turn the ignition OFF then ON again. Go to TPMS
Calibration.
TPMS Calibration
NOTE: If the tire pressures were not already set, make
sure the cold tire pressures are inflated according to
the doorjamb label.
1. Turn the ignition switch ON, or press the engine
start/stop button to select the ON mode.
2. All except Touring Models: Press and hold the
TPMS button for 3 seconds.
3. When the calibration begins, the indicator blinks
twice, then go to step 7.
4. Touring models: Press and hold the
INFORMATION button on the steering wheel to
enter the vehicle settings mode.
5. Press the SEL/RESET button on the steering wheel
to select TPMS CALIBRATION.
6. When the calibration successfully begins,
“Calibration Started” will be displayed on the MID
when the system receives the calibration.
7. Disconnect the jumper battery, start the vehicle and
verify that the VSA and the Low Pressure indicators
come on and go out.
8. Turn the ignition OFF, exit the HDS, and disconnect
the MVCI.

13-104

3 of 3