SB-10054477-8552

GM Bulletin No.: 13196A
Date: December 2013

Service Bulletin

SERVICE UPDATE
SUBJECT:

Service Update for Inventory and Customer Vehicles
Right or Left Low Beam Failure DIC Message
Expires with Base Warranty

MODELS:

2013 Cadillac ATS
Equipped with Adaptive Forward Lighting (T4F)

This bulletin has been revised to include U.S. and Canadian vehicles. Please discard all
copies of bulletin 13196.
This service update includes vehicles in dealer inventory and customer vehicles that
return to the dealership for any reason. This bulletin will expire at the end of the involved
vehicle's New Vehicle Limited Warranty period.
PURPOSE
This bulletin provides a service procedure to reprogram the headlamp control module on certain
2013 model year Cadillac ATS vehicles equipped with adaptive forward lighting (T4F).
During vehicle start-up, a low voltage condition at the headlamp ballast may set a DTC. The
DTC may be interpreted as a lamp outage and either the Right or Left Low Beam Failure
message may display in the Driver Information Center (DIC). This condition is intermittent and
even though the message is displayed, all exterior lamps still function properly.
This service procedure should be completed as soon as possible on involved vehicles
currently in dealer inventory and customer vehicles that return to the dealer for any type
of service during the New Vehicle Limited Warranty coverage period.
VEHICLES INVOLVED
All involved vehicles are identified by VIN in the Global Warranty Management System –
Investigate Vehicle History Application. Dealership technicians should always check this site to
confirm vehicle involvement prior to beginning any required inspections and/or repairs. It is
important to routinely use this tool to verify eligibility because not all similar vehicles may be
involved regardless of description or option content.
Additionally, a list of involved vehicles currently in dealer inventory is available on the “Service
Update Bulletin Information” link under the “Service” tab in GM GlobalConnect (US) or attached

Page 2

December 2013

Bulletin No.: 13196A

to the GlobalConnect message (Canada) used to release this bulletin. Customer vehicles that
return for service, for any reason, and are still covered under the vehicle's base warranty should
also be checked for vehicle eligibility.
PART INFORMATION
No parts are required for this update.
SERVICE PROCEDURE
Do not attempt to order the calibration number from GM Customer Care and Aftersales. The
calibration numbers required for this service procedure are programmed into control modules
via a Multiple Diagnostic Interface (MDI) with the calibration update. When using an MDI for
reprogramming, ensure that it is updated with the latest software version. Use TIS2WEB on or
after 06/28/13 to obtain the calibration. If you cannot access the calibration, call the Techline
Customer Support Center and it will be provided.
1. Verify that there is a battery charge of 12 to 15 volts. The battery must be able to maintain a
charge during programming. Only use an approved Midtronics® PSC 550 Battery Maintainer
(SPS Programming Support Tool EL-49642) or equivalent to maintain proper battery voltage
during programming.
2. Reprogram the Headlamp Control Module. Refer to SI and Service Programming System
(SPS) documentation for programming instructions, if required.
2.1 Connect the MDI to the vehicle.
2.2 Select J2534 MDI and Reprogram ECU from the SPS Select Diagnostic Tool and
Programming Process screen.
2.3 Select K26 Headlamp Control Module -- Programming from the SPS Supported
Controllers screen.
2.4 Follow the on-screen instructions.
3. Select the “Clear All DTCs” function on the SPS screen at the end of programming.
WARRANTY TRANSACTION INFORMATION
Submit a transaction using the table below. All transactions should be submitted as a ZFAT
transaction type, unless noted otherwise.
Labor
Code
9100074

Description
Headlamp Control Module Reprogramming

Labor
Time
0.3

DEALER PROGRAM RESPONSIBILITY
Whenever a vehicle subject to this service update enters your vehicle inventory, or is in your
facility for service in the future, and the vehicle is still covered under the New Vehicle Limited
Warranty, you must take the steps necessary to be sure the service update correction has been
made before selling or releasing the vehicle.
GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that
may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the tools,
equipment, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to
your vehicle, or that your vehicle will have that condition. See your dealer for information on whether your vehicle may benefit from the information.

We Support
Voluntary Technician
Certification