Service Program
Trucks

Mack Trucks, Inc.
Greensboro, NC USA

Date

Group

No.

Release

Page

9.2013

284

047

01

1(4)

Engine Control Module (ECM) Software
Update
MP10 US07
TD
SB-10054475-4671

PI0828, Engine Control Module (ECM) Software
Update
(September 2013)

Information
Software updates with enhancements to Peak Cylinder Pressure (PCP) balance capabilities
are available for the engine control module (ECM) on MACK TD vehicles equipped with
MP10 engine and US07 emissions.

Required Tools
Premium Tech Tool version 2.02.50 or higher or version 1.12.420 or higher
Diagnostic Connector 88890302 or 88890304
Communication Interface 88890300 or 88890020 with firmware 1.12.0.2 or higher

PV729-PI0828

USA61896

Mack Trucks, Inc.
Service Program

Date
9.2013

Group

No.

Release

284

047

01

Procedure
DANGER
Do not attempt to repair or service this vehicle without having sufficient training, the correct
service literature and the proper tools. Failure to follow this could make the vehicle unsafe
and lead to serious personal injury or death.
Note: Information is subject to change without notice.
Illustrations are used for reference only and may differ slightly from the actual engine
version. However, key components addressed in this information are represented as
accurately as possible.

You must read and understand the precautions and guidelines in Service Information,
Function Group 20, Engine Safety Practices, before performing this procedure. If you are
not properly trained and certified in this procedure, ask your supervisor for training before
you perform it.
1 Secure the vehicle for service by parking it on a flat level surface, applying the parking
brake, chocking the rear wheels, and placing the transmission in neutral or park.
2 Verify service program eligibility by checking service program status in eWarranty.
3 Connect Premium Tech Tool (PTT) to the vehicle diagnostics connector using the 9 pin
connector 88890034 and Communication Interface 88890020 or 9 pin connector
88890302 and Communication Interface 88890300. Connect the PC to a network
connection and a 120 Volt AC source.
4 Turn the ignition switch “ON”.
5 Log in to PTT and Identify Vehicle is displayed.

Page
2(4)

Mack Trucks, Inc.
Service Program

Date
9.2013

Group

No.

Release

284

047

01

6 Once the vehicle has been identified, enter the Work Order Number information, then click
Start Work.

W2079940

7 From the Main Menu select Program and then Function Group 2, MID128 ECU
Programming. Then click Start.
Note: The steps in this bulletin reflect the content in PTT 2.02.45. PTT 1.12.420 is similar.
8 Select Reprogram control unit with complete software package.
9 Certain conditions must be met to continue with programming. When all conditions have
been met, click Continue to proceed with programming.
10 When programming is complete, click Exit to return to Main Menu.
11 Clear any diagnostic trouble codes (DTC) and Finish Work.

Page
3(4)

Mack Trucks, Inc.
Service Program

Date
9.2013

Group

No.

Release

284

047

01

Reimbursement
This repair is covered by an authorized Service Program. Reimbursement is
obtained via the normal claim handling process.
Claim Type (used only when uploading from the Dealer Bus. Sys.)

41

Recall Status
Vehicle inspected, repair not required

1- Inspected
OK

Vehicle repaired per instruction

2- Modified
per
instruction

Labor Code
Primary Labor Code

2304C-16-96
— 0.4 hrs.

Time to take charge and determine campaign status

101AA-0A00 — 0.3
hrs.

Causal Part

3092091

Authorization Number

PI0828

Expiration Date

30-JUN2014

Note: Take Charge Time is not included in the Labor Code for this operation. Take charge
may be eligible but can only be used once per repair visit. If vehicle is having other warranty
repairs performed, take charge should be charged to the warranty repair, otherwise take
charge can be charged to this service program.

Page
4(4)