SB-10044367-3857

TECHNICAL BULLETIN
LTB00429NAS2
31 MAY 2012
ISSUE ‘2’ CHANGES ARE HIGHLIGHTED IN GRAY
SECTION: 303

Poor Engine Performance at High Altitude
AFFECTED VEHICLE RANGE:
LR3 (LA) 4.4L V8 only

VIN: 5A000360 – 9A513325
Model Year: 2005 - 2009

Range Rover Sport (LS) 4.4L V8 only

VIN: 6A900290 – 7A999999;
7A100000 – 9A215618
Model Year: 2006 - 2009

CONDITION SUMMARY:
Situation: The engine may exhibit poor performance / reduced power while driving at altitudes above 8,200
feet (2,500 meters) and the engine Malfunction Indicator Lamp (MIL) may be illuminated with Diagnostic
Trouble Codes (DTC) P0101, P0172, and/or P0175 stored in the Engine Control Module (ECM). This may be
caused by the calibration altitude limit.
Action: In the event of a customer concern of the above, refer to the Repair Procedure outlined below to
update the ECM software.

PARTS:
No parts required

TOOLS:
IDS with latest IDS-DVD and Calibration File; first available on IDS-DVD130.01 Calibration File v107
Land Rover-approved Midtronics Vehicle Power Supply

WARRANTY:
NOTE: Repair procedures are under constant review, and therefore times are subject to change;
those quoted here must be taken as guidance only. Always refer to DDW to obtain the latest repair
time.
DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a
quantity of zero.
SRO

DESCRIPTION
Update ECM software

12.90.13

TIME
(HOURS)

CONDITION
CODE

0.20

42

CAUSAL
PART
NNN500451

Normal Warranty policies and procedures apply

NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools, and
equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some vehicles, or
provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are
not a Retailer, do not assume that a condition described affects your vehicle. Contact an authorized Land Rover service facility to
determine whether this bulletin applies to a specific vehicle.
© Jaguar Land Rover North America, LLC

555 MacArthur Boulevard

Mahwah, NJ 07430

REPAIR PROCEDURE
UPDATE THE ENGINE CONTROL MODULE SOFTWARE
CAUTION: Ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform these
steps may cause damage to control modules in the vehicle.
CAUTION: A Land Rover-approved Midtronics Vehicle Power Supply must be connected to the
vehicle battery during IDS diagnosis / module programming.
1. Connect the Land Rover-approved Midtronics Vehicle Power Supply to the vehicle battery.
2. Turn ignition 'ON' (engine not running).
NOTE: IDS must be loaded with IDS-DVD130.01 v107 or later.
3. Connect the IDS to the vehicle and begin a new Symptom Driven Diagnostics (SDD) session.
4. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle.
5. From the Session Type selection screen, choose 'Diagnosis'.
NOTE: One or more of the following DTCs must also be stored in the ECM: P0101, P0172, or
P0175.
6. Select the 'Selected Symptoms' tab, and then select:
•

Electrical > Instruments > Warning lamps > Engine malfunction lamp > Lamp illuminated or

• Powertrain > Engine system – Engine performance > Poor acceleration and lack of power
7. Select 'continue'.
8. Select the 'Recommendations' tab.
9. From the Recommendations tab, select 'Run' to configure the 'Powertrain control module'
• Follow all on-screen instructions to complete this task.
10. Exit the current session.
11. Disconnect the IDS and the Midtronics Vehicle Power Supply from the vehicle.