permission of the publisher.

Technical Service Bulletin
Tip: Sporadic communication DTCs will be created during the flash procedure and will be automatically
erased along with all other pre-existing sporadic DTCs at the end of the SVM update test plan.
2. Tuning is the addition or modification of any component that causes an Audi vehicle to perform outside the
normal parameters and specifications approved by Audi of America, Inc. If you encounter a vehicle with a
tuned engine control module (ECM) or transmission control module (TCM), your dealership must do the
following before performing any procedure that updates ECM or TCM programming:
a. Notify the owner that their ECM or TCM was found to have been tuned.
b. Notify the owner that any damage caused by the tuning of the ECM or TCM (including any adverse
emissions consequences) will not be covered by Audi of America, Inc. warranties.
c. Obtain the owner's written consent (see attached Control Module Tuning form) for any requested repair under warranty or outside warranty - that requires flashing that will automatically overwrite the tuned
program.
Tip: Any programming update (flash) may overwrite any tuned ECM or TCM programming.
3. Ensure the TSB stating the condition in the vehicle applies to the customer complaint and the operator has a
valid GeKo user ID and password. Perform only operations explicitly stated in the TSB or RVU.
4. Verify that the following tester requirements are met:
• VAS 5051B Minimum Base CD Version 12.00.
• VAS 5051B/5052 Minimum Base CD Version 12 with Brand CD 12.61 installed.
• VAS Base Software Patch CD (Audi Technical Literature item number 42BaseSoftwarePatch) is installed in
the VAS 5051 / 5052. This patch is already in Base 12.0.
• VAS 5051X is plugged into a 110V AC power supply at all times.
• Connect 5051B and 5052/A to the local network.
• For A4s after VIN 8E_5A400000 (B7 Platform), always use the 6017B K Line Adapter to ensure
communication to all modules.
• If the wireless VAS 5054A transmitter head is used in conjunction with a VAS 5052A or VAS 6150 tester,
the transmitter head must be connected with a USB cable to the tester.
• Ensure the Windows power savings are set correctly (disabled) for VAS testers operating with an open
Windows interface in which users have access to all regular PC operating system functions (implemented
by running the Base V14.00.00 Recovery DVD).
Note:
If the Windows screensaver activates during a control module software update and the hard drive shuts
down as a result of the power settings, a control module failure may result. Refer to Service Circular ATE08-23 for more information.
Note:
Do not use a 6017 or 6017A while flashing. Doing so may result in complete control module failure.
5. Verify that the following vehicle requirements are met:
• Battery must have a minimum no-load charge of 12.5V.
• Connect vehicle to a powered Audi-approved battery charger. Do not use a trickle charger or battery
maintainer.
• Turn off the radio and all other accessories, and when necessary, switch off running lights by applying the
emergency brake or through the MMI option menu.

Page 3 of 7
© 2010 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written
permission of the publisher.

Technical Service Bulletin
• Turn off any appliances with high electromagnetic radiation (such as mobile phones).
• If communication with a module cannot be properly established, appropriate repairs must be made before
attempting SVM. If the tester cannot communicate with a module, the tester cannot flash software onto the
module.
6. Enter the SVM update into the User Test Plan by selecting the Audi Flashing option at the main tester
screen.
Tip: If you do not have the latest Base/Brand CD installed on the tester, then the SVM code may fail and
return an “ASM-MCD base system error” because the tester is not capable of reading the software flash
file. Starting with the MY 2010, some software files have changed and cannot be read with base tester
software level 15 or lower. Level 16 or higher must be installed on the tester along with all released patches
found on ServiceNet.
VAS Tester Patches can be found using → www.AccessAudi.com >> Special Tools and Equipment >> VAS
Tester Information >> Software.
7. Follow the SVM update procedure and enter the SVM Action Code found in the appropriate TSB when
prompted.
8. Enter your GeKo ID when requested. Data will be transmitted to the SVM server, and the server will respond
with instructions to continue. (See detailed descriptions in the Response Codes table below.) The procedure
may include one, or any combination of the following, for one or multiple control modules as specified in the
TSB or RVU:
• Update a control module (flash).
• Code a control module.
• Parameterize a control module.
• Check a control module.
This will occur when SVM does not recognize the control module as valid for the vehicle. If there is no
customer concern and no DTC regarding this control module, report the issue to the Technical Assistance
Center (TAC) with the required information specified in the Additional Information section below. For MMI
control units, it is possible the SVM code for feedback documentation was not performed after an update
via CD was performed. Always report MMI issues to the TAC before attempting a repair.
9. Always continue until the following text is displayed: Vehicle conversion/update has been successfully
performed. The changes have been stored in the system. Thank you.
Tip: The SVM Process must be completed in its entirety so the database receives the update
confirmation response. A warranty claim may not be reimbursed if there is no confirmation response to support
the claim or if action that is not explicitly stated in the TSB or RVU is taken.
10.Verify that all steps or special procedures mentioned in the TSB/RVU have been carried out. Then finish the
test plan and exit GFF via the Go to button. Answer the Warranty questions accordingly and print out or save
the diagnostic log when prompted.
Tip: During the flash procedure, an estimated time will be shown. This value is not used for actual SRT
calculation.
Response Codes
SVM can provide a response code with a repair suggestion or after a successful repair. The response code will
appear in the diagnostic log.

Page 4 of 7
© 2010 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written
permission of the publisher.

Technical Service Bulletin
Code

Description

Action to be taken

Perform an SVM Specified/Actual comparison and carry out
ERP0031I The SVM Code was
the coding or parameterization suggestion.
*
successfully processed but a
coding or parameterization of a
control unit may still need to be
performed.
ERP0032I The control unit(s) to be
*
updated does not match the
requirements for the SVM
code.

The control unit installed in the vehicle is not part of the SVM
update, the control module installed on the vehicle is not
talking on the CAN bus, or the part on the vehicle is older than
the original part. Ensure the correct SVM Code was entered,
ensure the TSB applies to the vehicle, and check the hardware
to ensure it’s correct for the vehicle. Perform a hard reset on
the module and retry the SVM code. If the hardware/software
levels of the replacement part are older than the original part,
then contact TAC because a new CARPORTA reference will
need to be created in the SVM system.

Follow the software update, new coding, or parameterization
ERP0033I Additional coding,
*
parameterization, or a software suggestion.
ERP0042I update may need to be carried
out as a result of the SVM
ERP0044I code.
ERP0046I
ERP0034I A hardware change suggestion A control unit installed on the vehicle is not correct for the
vehicle for one of the following reasons. Either the control unit
*
from an SVM Code or SVM
is incorrect for the vehicle (compare results of ETKA FI Search
ERP0045I Specified/Actual comparison.
versus Part Number search) or the control unit is of an older
ERP0048I
vintage than the original part installed on the vehicle (old stock
service part). Additionally it is possible a software update using
a CD was performed on the MMI system without the proper
SVM Code being executed after the update. If the part is
confirmed to be newer than the original part, then on a rare
occasion, the part being installed can be missing from the
SVM system. If this is the case, then a hardware change will
be suggested since the part is not known to the system. In the
event this occurs, please contact TAC so the SVM system can
be updated.
ERP0038I The control unit(s) to be
updated does not match the
requirements for the SVM
code.

The control unit installed in the vehicle is not part of the SVM
update or the control module installed on the vehicle is not
talking on the CAN bus. Recheck to make sure the correct
SVM Code was entered, make sure the TSB applies to the
vehicle, and check the hardware to ensure it’s correct for the
vehicle. Perform a hard reset on the module and retry the SVM
code.

Page 5 of 7
© 2010 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written
permission of the publisher.

Technical Service Bulletin
ERP0039I The SVM Code performed
successfully.
*

All necessary actions taken by the SVM code were performed
successfully. Nothing additional is required.

ERP0040I
ERP0050I
ERP0041I The SVM Code performed
successfully but there are still
repair suggestions to other
Control Units not featured in
the SVM Code update.

A control unit installed on the vehicle is not correct for the
vehicle or the SVM Code for document feedback was not
performed after a CD update was performed on the MMI
system.

ERP0043I Additional coding and/or
parameterization needs to be
performed

Follow the new coding or parameterization suggestion.

* The response code is specific to an SVM code that affects the MMI system (i.e. when an SVM code is
performed after an MMI CD update, these response codes are returned).
A

CARPORT is the database in Germany that contains all control unit information (part numbers and software
versions) for each vehicle produced by AUDI AG.

Warranty
This TSB is informational only and not applicable to any Audi warranty.

Additional Information
Checking for Internet Connectivity
With the tester connected to the internet, add and carry out the SVM Communication Test to the GFF test plan
which can be found here:
Audi Flashing >> SVM Communication, Checking
or
GFF >> Go To >> Function/Component Selection >> SVM >> SVM Communication, Checking
GeKo Registration and ID Check
To obtain a GeKo user ID and password, follow the instructions in the GeKo ID Request form found here:
→ www.audi.techliterature.com >> Service >> Documents >> Service and Repair >> GeKo ID Request Form
(located on the 2nd page listing)
To check your GeKo ID, perform the following test from the Tester Startup Screen with the tester connected to the
internet:
Administration >> Network Settings >> GeKo Test
Testing the SVM Connection
SVM Communication checking. It will ask for your user ID and Password. If the test fails, change the port, cord,
and/or tester and run this test again.

Page 6 of 7
© 2010 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written
permission of the publisher.

Technical Service Bulletin
Further Tester Assistance
If any of the listed troubleshooting procedures and/or checks result in errors or yield no solution and further
assistance is required, please follow these steps:
1. Utilize the information contained in the Function Description button in the tester at the point of the error.
2. Report the problem to the shop network administrator for further investigation.
3. Contact the responsible support team for further assistance:
• Service Department Applications (GeKo, ElsaWeb, and ServiceNet): 866-892-3375.
• VAS 5051/5052 Software Subscriptions: Orders need to be placed via → www.audi.techliterature.com
• VAS 5051/5052 Software Support: 888-896-1298.
Technical Assistance Center Contact Requirements
Contact the TAC via the Technical Assistance Contact System in ElsaWeb in cases where there is a clear
technical issue with the vehicle or response from the SVM system. Always include the following information in the
ticket:
• SVM Action Code attempted.
• Control module(s) address word(s) that are in question.
• The complete tester diagnostic log from the GFF session.
All parts and service references provided in this TSB are subject to change and/or removal. Always check with
your Parts Dept. and service manuals for the latest information.

Page 7 of 7
© 2010 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written
permission of the publisher.

Owner Acknowledgement of Control
Module Tuning and Authorization
to Reprogram Control Modules

Date:
Dealer Number:
Vehicle Identification Number:
Repair Order Number:
Dealer stamp

Tuning is the addition or modification of any component that causes an Audi vehicle to perform outside the
normal parameters and specifications approved by Audi of America, Inc.
I, _____________________________________, owner or driver of the above-identified Audi, confirm:
‰

Tuning (especially power-increasing modifications) has not been performed on my vehicle.

‰

Tuning has been performed on my vehicle. The following components were modified or installed:

Please provide the name and telephone number of the company that performed the tuning if you
wish us to contact them:

I understand that if my control module is determined to have been tuned, any damage caused by the
tuning of the control module (including adverse emissions consequences) will not be covered by Audi of
America, Inc. warranties.
I am permitting an authorized Audi dealer to reflash (update) my controle module, and by so doing, I
understand that this process will automatically overwrite (destroy) and permanently delete any tuning
program that was previously installed on the control module of my Audi vehicle.
By signing below, I fully acknowledge and understand that the tuning program will not be restored and
Audi of America, Inc., will not be liable in any way for the loss of tuning data.

Signature of Customer

© 2010 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the
copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without
notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.