Date: 2014-08-22

Ford Motor Company

NHTSA Action Number: PE14027

Components: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS

Subject:

Front brake hose failure

Opened From: 2014-08-22 - 2015-02-03

NHTSA Recall Number:

Summary

The Office of Defects Investigation (ODI) opened PE14-027 based on a report of 13 front brake hose (jounce hose) failures in 11 vehicles in the District of Columbia Metropolitan Police Department (DCMPD) fleet of 46 model year (MY) 2013 Ford Explorer Police Interceptor (PI) vehicles (VOQ 10621634).The DCMPD fleet provided Ford with 71 jounce hoses for analysis, including 4 of the 13 failed hoses.Inspection of each of the failed hoses identified a small tear in the outer cover on the body end of the hoses on the outboard side. Ford?s lab analysis of these hoses identified splits in the inner liners 1.5-2.0mm from the end of the nipple (outside of the crimped ferrule joint).Ford conducted pressure testing of 10 randomly selected samples of the remaining 67 hoses that had not experienced leaks and 9 of the samples leaked at 6,000 psi.Ford?s examination of the 9 hoses that leaked in the pressure tests found 4 that failed on the outboard side of the hose (similar to the 4 leaking field parts) and 5 that failed on the body end of the hose on the inboard side.Four additional non-leaking hoses were sent to the hose supplier, Hitachi, for analysis.Broken yarn was observed in scanning electron microscope examinations at both the body side and caliper side hose to ferrule crimps, indicating severe bending stress had occurred at these locations. Hitachi supplied an additional set of non-leaking field return hoses and a brand new set of hoses to an outside laboratory (Element Materials Technology) for analysis.The lab did not identify any manufacturing or material deficiencies in the hoses and concluded that the hose failures were caused by excessive bending stresses.Based on the examinations of the returned jounce hoses, Ford conducted durability testing on new hoses that were the same design as those found on the subject vehicles.Ford first determined the worst case conditions for the hoses; jounce bumpers removed, internal rebound stops fully compressed, and shock absorbers attached. With the jounce hose installed, the steering was rotated to the maximum turn angle while the suspension was translated from full jounce to full rebound.This determined the maximum hose length of 13.0in (331mm) and a minimum hose bending radius of 1.6in (40mm).Using these conditions hoses tested on a Suspension Motion Simulator far surpassed Ford?s performance specifications. Twenty (20) complaints of front brake jounce hose failure were identified on a total of 18 Explorer PI vehicles, including the 13 hose failures in 11 vehicles from the DCMPD fleet that prompted PE14-027.The remaining 7 complaints included 3 from one fleet that reportedly occurred on the banjo block end of the hose assembly and single complaints from 4 other fleets.Only two brake hose assemblies were used in the subject and peer Explorer vehicles, with the BB53 level hose used until June 20, 2012, and an updated DB53 level hose used thereafter.No pattern of failures was observed by hose assembly, with 15 of failures involving the BB53 hose assembly (including the 13 from DCMPD manufactured in March 2012) and 5 the DB53 hose assembly built after June 20, 2012. No root cause was determined for the reported Explorer PI jounce hose failures, but Ford identified improper service repair procedures (e.g., hanging the brake caliper from the brake hose during brake pad replacement) as a possible contributor to higher than expected rate of front brake jounce hose leaks. ODI?s analysis of field data, hose inspection and test data did not identify evidence of any defects in hose material, manufacture or vehicle installation.The closing of this invest

Investigation Documents

For Latest Documents related to this Investigation, visit the NHTSA Website.

Click the (+) Plus Sign

Then click Associated Document(s).

SaleBestseller No. 1

Valvoline DOT 3 & 4 Synthetic Brake Fluid with High Boiling Point, Corrosion Protection, Vapor Lock Resistance, Compatible with ABS, Disc and Drum Brake Systems, 32oz

• Mixes well with conventional fluids
• Low-moisture formula provides excellent vapor lock...
• Ideal for hydraulic and disc brakes

$12.49 −$2.31 $10.18

Buy on Amazon Price incl. tax, excl. shipping

Bestseller No. 2

Prestone AS401 DOT 3 Synthetic Brake Fluid - 32 oz.

• Provides an extra margin of safety in extreme braking...
• Mix of polyglycol ethers ensures hot brake-system operation...
• Excellent for ABS, disc and drum brake systems
• Delivers braking power when needed by avoiding a spongy...
• Both wet and dry boiling points exceed the minimum...

$9.38

Buy on Amazon Price incl. tax, excl. shipping

Last update on 2026-06-21 / Affiliate links / Images from Amazon Product Advertising API

---

 

Search NHTSA Database for Recalls

Recalls List

Search NHTSA Database for (TSB's) Technical Service Bulletins

Technical Service Bulletins TSB's List

Search NHTSA Database for Vehicle Complaints

Complaints List