Service campaign agreed with CARB. Problem: Lateral and longitudinal acceleration sensors need to be monitored by the OBD system. Solution: Introduction of diagnosis for lateral and longitudinal acceleration sensors.
If the PDF is very large, it may not load in the preview below.
TSB/Document ID: L74X-A.11.25
- Identifier the manufacturer uses to identify the communication and the way it can be located by those searching for it.
Replacement Service Bulletin Number:
- Replacement service bulletin number.
MFR Communication Date: 2025-04-04
- Date the communication was disseminated by the manufacturer.
MFR Internal Campaign ID/Software Version:
- Manufacturer's unique identifier for the service campaign if this communication is a related one.
Communication Type: Service Campaign
- Service Bulletin / Repair Instructions
- Service Campaign
- Warranty Program / Extension
- Over The Air
- Emissions
- Other
NHTSA Components: POWER TRAIN
- NHTSA Component(s) of the products involved in communications.
MFR Component System:
- Manufacturer's top-level component of the products involved in communications.
MFR Component Subsystem:
- Manufacturer's component subsystem of the top-level component identified above.
To:
Object:
Date:
Pages
L74XA.11.25
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
Campaign code:
L74X-A.11.25
Campaign name:
BL4.6 Update PN_47B990100C_Rev_0131_0132
Model:
Revuelto
Model Year:
2024
Markets:
Italy, Germany, United States, Canada, United
Kingdom, Denmark, Belgium, France,
Netherlands, Sweden, Luxembourg, Spain,
Portugal, Greece, Monaco, Poland, Azerbaijan,
Czech Republic, Austria, Romania, Estonia,
Turkey, India, Singapore, Lebanon, Indonesia,
United Arab Emirates, Qatar, Saudi Arabia, New
Zealand, Bahrain, Kuwait, Taiwan, Thailand,
Mexico, Malaysia, Philippines, Switzerland,
Cambodia, Oman, Peru, Latvia, Hungary, South
Africa, Macao, Vietnam, Hong Kong, Australia,
Brazil, Norway
VIN Involved:
From RLA00042 To RLA01883
Important information: before proceeding with
the repair, connect to the Warranty Portal and,
using the “VIN Info” function, check that:
•
The vehicle is affected by the instructions
contained in this bulletin.
NOTE: some vehicles may not be affected,
despite the fact that their Vehicle
Identification Number (VIN) falls within the
range.
•
Only replacement parts that correspond to
the specific operation, identified by a
letter (such as A, B, C, etc.), are to be used
for the chassis being repaired.
Example
Rev.00
CONFIDENTIAL
N.B.:
Operation A will be available only when the
instructions require a preliminary check to be
performed to determine whether or not the
vehicle actually needs updating.
Information for the service network:
During ongoing product monitoring, Automobili
Lamborghini S.p.A. informs you that a new baseline software update is now available.
Solution for the field:
Update the car as stated in the follow instructions.
IMPORTANT!
Before carrying out the operations contained in
this bulletin, please execute any other campaigns
planned for this vehicle in the time order in which
they were issued. The time order can be identified
by the name of the bulletin. Example: L62X-A04.19 is bulletin number 4 of 2019.
Spare Parts:
None
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
1/19
To:
Object:
Date:
Pages
L74XA.11.25
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
Management of replaced parts:
Store the components that have been removed
from the vehicle in an appropriate manner, marking them with their corresponding bar codes so
that they can be identified during visits by the
competent Area Manager.
Important information:
attach all documents generated during the work
carried out, evidence of the work itself, for
instance work orders and diagnostic protocols
with BETA-Reports.
If one or more of these is missing, it may lead to a
rejected reimbursement request.
Labor time:
Operation B: 3,0 h
Previous bulletins superseded.
None
Fill out the page in the warranty booklet
(identified in the image below) in the section
“Service and Recall Campaigns”:
Warranty claims instructions:
To request reimbursement for the repair
performed, access the “LIASS” system on the
Lamborghini
portal
and,
following
the
instructions in the system’s “Manuals” section,
generate and fill out a Warranty Request.
Select the required campaign and proceed with
entry; carefully read the options present in the
alert message that displayed by the system (see
example) and select the option performed on the
vehicle.
Tools/Materials required
Code
Description.
Reimbursement will be structured as follows
based on the operation performed:
-
n\a
n\a
Q.ty
n\a
OPERATION B:
o
o
Steps to be executed: I to VII
Labor time: 3,0 h
At the end of the steps mentioned in the Operation B, the following ECUs will have the following
SWs target:
ECU
Engine Master 01
Transmission 02
Brake 03
Engine Slave 11
Infotainment 5F/17
Rev.00
CONFIDENTIAL
N.B.
All O.D.I.S. Service technical documentation can
be viewed on the Lamborghini web portal, in the
O.D.I.S. Sel Service app.
SW version
0014
0010
0181
0014
419
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
2/19
To:
Object:
Date:
Pages
L74XA.11.25
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
Preliminary operations:
The instructions contained in this bulletin are
based on the O.D.I.S. Service diagnosis software
updated at the last version. Please, make sure
that O.D.I.S. Service is properly updated on your
laptop.
IMPORTANT!
Before carrying out the operations contained in
this bulletin is mandatory to install the last Hotfix
available at the following DMS link:
To do that, open O.D.I.S Service and check if are
present one of the icons shown in the images below:
Lamborghini DMS → ROOT → Service → Diagnosis → Documents → O.D.I.S. Service → Download
→ O.D.I.S. Service HOTFIX
1.
Update O.D.I.S Service by uninstalling and
reinstalling the SW: further instructions
available on the O.D.I.S Self Service APP.
IMPORTANT!
Before carrying out the operations contained in
this bulletin please perform the following campaign: L74x-A.31.24_BL4.4_Update_EN_rev01
NOTE:
It is essential that you connect an appropriate
battery charger to the charge points available in
the luggage hood (front center of the vehicle).
The voltage must remain constant above 13V: Set
the battery charger and check the voltage status
directly on O.D.I.S Service, as shown below:
2. O.D.I.S Service “Automobili Lamborghini”
post-setup update
If one of these icons appear, please proceeded to
update O.D.I.S Service.
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
3/19
To:
Object:
Date:
Pages
L74XA.11.25
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
Repair method:
The updating procedure described here includes
the following steps:
3. In the main page of SD Creator fill out the
Model and Part Number fields:
Download SW from SD-Creator sw 419;
Enable Engineering Menu;
ECU 5F/17 update to SW 419;
ECU 0019 check DTC;
ECU 11 update to SW 0014
SVM update and configuration;
Erase fault memory;
I.
Download Software from SD-Creator
software 419
1. In order to download the necessary software
for the update procedure, open on your laptop
the software SD Creator by a double click on
the program icon.
2. When the program starts, fill in the Windows
screen fields as explained in the “BI09.17_[ENG]_SD-Creator installation package
procedures".
a. Select the Model, (Revuelto);
b. Insert the USB-C stick and type the Part
Number specific for your destination
market making reference on the table
at following point.
4. Select the Part Number related to the destination market of your vehicle:
Table of reference for control unit 5F (Infotainment System)
Part Number
Software Target
Destination Market
616.530.033.71
419
All markets except
Japan and China
5. Through the selected Part Number, the version of the ECU 5F software suitable to the selected market will be downloaded. Then, click
“Search”. The following image is only for example purposes:
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
4/19
L74XA.11.25
To:
Object:
Date:
Pages
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
6. If the entered part number is correct, following the search, will be shown the model name
and the required size of the USB memory stick
to generate the software. E.g. image:
IMPORTANT:
Before start to download the software!
The process involves formatting the USB-C stick
and deleting the files inside it.
In order to avoid losing the data, it is advisable to
use empty USB-C stick.
Make sure that the available storage space is
larger or at least equal to the size required by SD
Creator.
7. Follow the instructions to download the software. Click the Start Button,
to start the software download process. The
software will be automatically saved in the
USB-C stick. E.g. image:
8. At the end of the process, green icons will appear on the right and positive feedback will be
displayed indicating the success of the operation. Click on the bar “
” in order to finish the download process. The USBC stick is automatically unplugged from your
laptop.
ATTENTION:
If the error shown in the following image occurs in
the download from SD Creator, perform the instructions at the end of this document, in Trouble
shooting section.
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
5/19
L74XA.11.25
To:
Object:
Date:
Pages
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
9. To verify the success of the operation, extract
and reinsert the USB-C stick and make sure
that the software required is present. The following image is an example concerning the
folders created.
IMPORTANT:
After enabling the engineering menu, please
leave the car in sleep for 15 minutes, key off, all
doors closed and locked, OBD disconnected.
III.
At this point the downloaded software is available
on the USB-C stick and ready to be flashed on the
car.
ECU 5F update to Software 419
12. Move in the car and insert the USB-C stick
containing the downloaded software 419 in
the USB1 port located under the Navi screen
(image below).
II.
Enable Engineering Menu
10. Select the tab “Control units”, select the ECU
5F and from “Guided Functions” select “5F –
Enable Engineering Menu”, then click on
“Run”.
13. To update the ECU 5F software it is necessary
to reach the Engineering Menu through the
following commands sequence on the central
display.
11. When request, please press option 1 to enable the engineering menu.
Rev.00
CONFIDENTIAL
14. Press and hold the top center screen for a few
seconds.
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
6/19
L74XA.11.25
To:
Object:
Date:
Pages
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
15. Press “System Information” button.
18. Select the file in the second tab and then
press “Select File” button.
16. Press “Update software" button.
19. Flag the button “I Checked the SDN compatibility matrix” and then press “START” button.
17. Select USB that contain the SW (file .zip).
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
7/19
To:
Object:
Date:
Pages
L74XA.11.25
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
20.Remove the USB-C stick only when the upload
will be ended.
21. Click on the button “Go to main menu” to return in normal visualization mode.
22. After the update, leave the car in sleep for 15
minutes, key off, all doors closed and locked,
OBD disconnected.
23. Repeat the step 10 and 11 to disable Engineering Menu.
IV.
ECU 0019 check DTC
V.
ECU 11 update to SW 0014
25. From the Lamborghini HUB, at the following
link, download and execute the flash data container:
DMS --> ROOT--> Service--> Diagnosis --> Documents --> O.D.I.S. Service --> Download -->
O.D.I.S Service Flashdatacontainer --> For Revuelto -->Lamborghini_Flash_Revuelto_BL4.6.exe
26. The following setup appear: Click on “Install”
and follow the instructions.
24. Check the DTCs from the ECU 0019: If the DTC
“C12A5F0: Vehicle electrical system configuration implausible” is present and is in “active”
status, please perform the GFF “Vehicle configuration implausible” from the Test Plan, as
shown below:
27. From the "Test plan" menu, click on the "Select
own test" box and then click on the magnifying
glass:
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
8/19
L74XA.11.25
To:
Object:
Date:
Pages
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
28. Enter in the search bar “Update programming”. Select the function “Update programming (Beta Version)” and click on “Go to”.
29. Click on “Attach to test plan”.
31. Select the control unit type to flash. In this select option “- 1. -“, “ASAM/UDS”.
32. Specify the control unit Diagnostic Address
and then click on “Apply” box. In this case insert “11”.
11
30. If the steps are successful, the function Update programming (Beta Version)" will appear
in the Test plan. Click now on the Update programming (Beta Version)” function and then
“Perform test”.
Rev.00
CONFIDENTIAL
33. Click on “- 1. -” if the selection is correct, otherwise click “- 2. -” for repeat program or “- 3.
-” for abort program.
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
9/19
L74XA.11.25
To:
Object:
Date:
Pages
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
34. Insert the name
“FL_47B907051_0014__V001”
FL_47B907051_0014__V001
VI.
SVM update and configuration
IMPORTANT:
Improper use of this function can cause damage
to the ECUs.
36. To start the procedure to execute an SVM
code, select the “Special functions” tab in
O.D.I.S. Service.
35. Select the extension of the file “.pdx”.
37. Click on “SVM– Code input (APSBL)” and
then on “Perform test”.
At the end of the update, O.D.I.S. Service will
show some data about control unit software version. Please check that the ECU 0011 SW version
is 0014.
38. Enter the code "L74XA1125" in the appropriate
space at the top right and click “Adopt”.
L74XA1125
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
10/19
L74XA.11.25
To:
Object:
Date:
Pages
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
39. The SVM code entered is again displayed in
the dialog box. If the entered code is correct,
click on “Yes”. Otherwise click on “No” to cancel the SVM procedure.
42. If the following error screen is displayed, the
error does not indicate an issue, please press
“Continue” and continue with the campaign.
43. It might become necessary to perform one or
more of the following operations in the SVM
procedure:
40.Wait for data to be acquired from all the control units. This operation requires a few
minutes.
•
Coding;
•
Parameterization;
•
Calibration;
•
SW Update;
44. To perform these actions, it is usually necessary to click on “Finished/Next” where requested and to follow the instructions directly
provided on the O.D.I.S. Service dialog
screens.
45. After the update, leave the car in sleep for 5
minutes, key off, all doors closed and locked,
OBD disconnected.
41. The SVM function will automatically continue
with identification of the control units in the
vehicle.
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
11/19
L74XA.11.25
To:
Object:
Date:
Pages
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
Please, execute the following steps:
IMPORTANT:
Trouble shooting for SVM ERP Error received:
From the "Test plan" menu, click on the "Select
own test" box and then click on the magnifying
glass:
•
•
•
8013 → please contact Technical Support
8088 → please contact Technical Support
8101 → please check the correct syntax of
SVM code inserted.
• 8113 → This error could have several resolutions:
a. If appear only the screen with error 8113, please
perform a 12V battery reset and a sleep cycle. Repeat SVM code and contact Technical Support if
not resolved.
b. If appear the following screens (ECU02 update
failed):
Enter in the search bar “Update programming”.
Select the function “Update programming (Beta
Version)” and click on “Go to”.
Please, follow the instructions displayed: switch
the ignition OFF and back ON after 10 seconds
and then click “Done/Continue” to continue.
c. If appear the following screen at the end of the
function (ECU02 update failed):
Rev.00
CONFIDENTIAL
Click on “Attach to test plan”.
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
12/19
L74XA.11.25
To:
Object:
Date:
Pages
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
If the steps are successful, the function Update
programming (Beta Version)" will appear in the
Test plan. Click now on the Update programming
(Beta Version)” function and then “Perform test”.
Select the control unit type to flash. In this select
option “- 1. -“, “ASAM/UDS”.
Click on “- 1. -” if the selection is correct, oth-erwise click “- 2. -” for repeat program or “- 3. -” for
abort program.
Insert the name
“FL_47B927256_0010_4821C523_V001_S”.
FL_47B927256_0010_4821C523_V001_S
Select the extension of the file “.pdx”.
Specify the control unit Diagnostic Address and
then click on “Apply” box. In this case insert “02”.
02
At the end of the update, O.D.I.S. Service will
show some data about control unit software version. Please check that the ECU02 SW version is
0010.
After the update, perform the guided function
“SVM – Code input” again (steps from 36 to 45).
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
13/19
To:
Object:
Date:
Pages
L74XA.11.25
•
•
•
•
•
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
8118 → please perform a sleep cycle. Be
sure the control unit 5F has been updated
to correct software (see previous steps).
Check the software level via 5f – control
unit identification and compare it to the
reference table. Repeat SVM code and
contact Technical Support if not resolved.
8037 → Please check your O.D.I.S Service
version and hotfix as indicated in “Preliminary operation” section.
9999 → for the owners of the new D3 Edge
Box, please refer to the informative bulletin BI.08.24 to check the correct O.D.I.S
Service connection setup.
ECU 0011 - Status 12 → the error does not
indicate an issue and can be continue with
the next step of the campaign. Please, select option 1 to go ahead.
ECU 0017 - Status 13 → the error does not
indicate an issue and can be continue with
the next step of the campaign. Please, select option 1 to go ahead
Rev.00
CONFIDENTIAL
•
•
ODS5003E → If the following screen appear please close and repeat the SVMCode.
IMPORTANT:
Trouble shooting for DTCs after SVM code:
If during the SVM Code input procedure, the follow errors appear:
•
ECU0074 → C10C500: Basic setting (deflected) not performed: please, from the
ECU 0074, execute the guided function
“74 - Ride hide full process”
Then click on basic setting "2 - Lifting system " and
follow the instructions directly from the O.D.I.S.
Service.
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
14/19
To:
Object:
Date:
Pages
L74XA.11.25
•
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
ECU00C5 → U020600: Lost Communication with folding top control module
From the "Test plan" menu. Click on the "Select
own test" box and then click on the magnifying
glass:
Click on “Attach to test plan”.
If the steps are successful, the function Update
programming (Beta Version)" will appear in the
Test plan. Click now on the Update programming
(Beta Version)” function and then “Perform test”.
Enter in the search bar “Update programming”.
Select the function “Update programming (Beta
Version)” and click on “Go to”.
Select the control unit type to flash. In this select
option “- 1. -“, “ASAM/UDS”.
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
15/19
To:
Object:
Date:
Pages
L74XA.11.25
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
Specify the control unit Diagnostic Address and
then click on “Apply” box. In this case insert “C5”.
Select the extension of the file “.odx”.
C5
Click on “- 1. -” if the selection is correct, oth-erwise click “- 2. -” for repeat program or “- 3. -” for
abort program.
At the end of the update, O.D.I.S. Service will
show some data about control unit software version. Please check that the ECU 00C5 SW version
is 0503.
Insert the name
“FL_47B965429D_0503__V001_S”.
FL_47B965429D_0503__V001_S
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
16/19
To:
Object:
Date:
Pages
L74XA.11.25
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
Final operations:
/* Diagnosis protocol saving */
VII.
49. Save the Diagnostic protocol as described in
the chapter “Saving a diagnostic protocol” on
app “O.D.I.S. Self Service Guide”, available on
Lamborghini HUB portal when the procedure
described in this document is completed.
Erase fault memory
46. Select the “Special Functions” card and then
“Erase fault memory - overall system” to delete all stored faults.
50.For the correct saving of the data after the SW
update, it is necessary to close O.D.I.S. Service, start a new diagnostic session and save
a new protocol. Both protocols must be attached to the Corresponding Warranty Request in LIASS.
47. The complete guide for deleting faults is available in the chapter “Reading/cleaning event
memory” on app “O.D.I.S. Self Service Guide”,
available on Lamborghini HUB portal.
IMPORTANT:
The Diagnostic Protocol must be attached to the
Corresponding Warranty Request in LIASS (to enter the request on the web portal, refer to the
W.Claim manual which you can consult in the
Warranty section of the portal).
48. Go back to the “Block diagram” card and select “Read all fault memories” from one of the
vehicle’s control units to update the display of
the faults present after deletion.
IMPORTANT:
Solve any faults still present by performing the
functions listed in the “Test plan”. Perform the
procedure “VII. Erase fault memory” again until all
faults are fully removed from the vehicle’s control
units.
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
17/19
To:
Object:
Date:
Pages
L74XA.11.25
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
Trouble shooting for generic issues:
If the following error screen is displayed,
abort the guided function by clicking on
“Cancel Test” and contact Technical Support.
If the following connection error is displayed like in the following example
screenshots:
-
If an error is displayed that regards the
hardware interface, and the "connection to
vehicle" and "key state" icons appear as
shown in the figure below:
-
Click “Cancel”;
Repeat installation of the interface
VAS6154/6154A/6154B for the instructions
in procedure (*) “Checking the VAS 6154”,
selecting the right-hand “Extras” menu in
O.D.I.S. Service and clicking on the “Diagnostic interface” button.
Rev.00
CONFIDENTIAL
It is not possible to connect to the central server; check that your laptop is correctly connected to the Internet and retry by clicking on “Yes” or “Done/continue”, as appropriate.
If the connection is dropped during the target/actual comparison during the SVM
procedure:
-
It is not possible to connect to the central server; check that your laptop is correctly connected to the Internet and retry by clicking on “1”.
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
18/19
To:
Object:
Date:
Pages
L74XA.11.25
After Sales Official Network
BL4.6 BL Update PN_47B990100C_Rev_0131_0132
/04/2025
19
If the same error type should reoccur during the application test, try the following
procedure:
-
Exit O.D.I.S. Service
Restart O.D.I.S. Service ensuring that:
1. You have a network connection
2. The O.D.I.S. Service connection is
set to Internet
-
Run the connection test again and perform the SVM again.
IMPORTANT:
If the following error should occur, it is necessary
to follow the instructions given in BI.25.18
(Rev.02), which can be downloaded on the Lamborghini HUB portal:
IMPORTANT:
The documents which must be provided together
with the operation under warranty request are:
-
Produced Repair Order
-
Saved Diagnostic Protocol with BETA
report
Failure to follow these procedures could lead to
the request being rejected.
For more information, please contact your Area
Manager or open a ticket to Technical Support in
Lamborghini KEY (Request – General Information
– After Sales Services - After Sales Technical
Support).
Regards,
Lamborghini Service
All O.D.I.S. Service technical documentation can
be viewed on the Lamborghini web portal, in the
O.D.I.S. Sel Service app.
Rev.00
CONFIDENTIAL
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili Lamborghini S.p.A pursuant to copyright law. The company reserves the right to make updates and
modifications as needed. The reprinting, reproduction, distribution to unauthorized persons and/or to third parties, and the partial or complete translation of the material contained herein are prohibited without the express
written consent of Automobili Lamborghini S.p.A.
Doc. no.: L/V6_M06 Rev.[07]
19/19
Enhanced Performance, Wider Vehicle Coverage: The VD70S OBD2 scanner offers fast, reliable and affordable professional diagnostics for both DIYers and professional technicians. Powered by a long-lasting 18.25Wh battery, it supports CAN FD, DOIP, and FCA protocol, ensuring compatibility with 100,000+ global vehicles. The upgraded V2.0 diagnostic report allows shop to add logo, customer details, and repair attachment - perfect for boosting credibility and streamlining workflows. With superior performance and broader vehicle compatibility, the VD70S car scanner keeps you ahead in automotive diagnostic
Pro Features, Home Mechanic Budget: Why pay thousands for dealer tools? The VD70S scan tool delivers advanced professional diagnostic at an affordable price, including 30x faster 66ft wireless scanning, 4000+ active tests, 36+ hot services, ECU coding, PMI function, and OE-level full-system scan with 8-in-1 data graph. It rivals expensive shop tools—perfect for DIYer, technician, and small shop. Get dealer-grade power without the cost—the VD70S obd2 scanner diagnostic tool makes pro diagnostic accessible to all
True Bidirectional Control for Precision Repair: VD70S car diagnostic tool gives you direct vehicle module control to test components like fuel pump, injector, A/C clutch, window and more, enabling you to accurately and quickly locate faulty components. Unlike basic code reader, our advanced bidirectional functionality lets you actively command system - like triggering the ABS pump to confirm your fix worked. With pinpoint component testing and real-time validation, you can diagnose intermittent issues faster and prevent costly return visits. The VD70S transforms complex diagnostic into precise, time-saving repair - giving professional-grade accuracy at an unbeatable value
66ft Wireless Freedom – No Cable, No Limit: Experience ultimate diagnostic flexibility with the VD70S scanner's industry-leading 66ft wireless range – move freely around your shop without losing connection. Unlike constrained wired tool, our dual-mode design includes both stable wireless operation and optional wired connectivity for latency-sensitive task. Professional technicians love how this wireless freedom revolutionizes bi-directional control: "Being able to activate components while moving around the vehicle is a game-changer for complex diagnostic" – Certified Master Tech. VD70S eliminates cable clutter while delivering rock-solid stability
Powerful & Affordable Auto Scanner with 36+ Special Functions: Take control of your vehicle maintenance and save hundreds in shop fees with the VD70S car diagnostic scanner. This advanced car tool performs 36+ hot services including TPMS reset, throttle body relearn, ABS bleeding, and electronic parking brake adjustment – all without paying $150+ per service at dealership. Besides, the VD70S unlocks 200+ vehicle-specific functions by tapping into the system menu in the diagnostic results, handling everything from basic reset to complex calibration. Text us your VIN + what you need and we’ll check the compatibility
Your Efficient Solution for Car Maintenance: The 2025 VD70 OBD2 Scanner Diagnostic Tool is designed by a professionals for automotive technicians, workshops, and DIY enthusiasts, ensuring no unnecessary costs are added to the price. It provides OE All Systems Diagnostics, 36+ Reset Functions, Bi-Directional Control, and ECU Coding, etc. With 2+64GB storage, an 18.25Wh battery, and 3 years of free updates, it’s built for both immediate and long-term use, offering dependable support for a wide range of vehicle maintenance tasks.
Why You Need a OBD2 Scanner with Bidirectional: With the VD70, you get a full bidirectional scan tool capable of performing 4000+ active tests. It can command car modules and receive data from the ECU to test components like EVAP, ABS pumps, windows, and more—all with one tool. This helps you pinpoint faults accurately, saving time and money by reducing trips to the shop and the need for multiple scanners. Whether you're a pro or a DIYer, this diagnostic tool simplifies complex diagnostics. Pro Tip: Send us your VIN before purchase to confirm compatibility.
36+ Special Functions & Vehicle-Specific Features: The VD70 OBD2 scanner offers 36+ services, including Oil Reset, EPB, BMS, Throttle Adaptation, Injector Coding, ABS Bleed, Crank Sensor Relearn and TPMS Reset. It also provides vehicle-specific functions include reset, adaptation, initialization, and calibration. These capabilities help you perform comprehensive tasks like system reset with ease. Note: Features vary by vehicle make and model. Please check compatibility with your VIN by contacting us at vdiagtool2 @ outlook . c o m before purchase.
Advanced ECU Coding & PMI for Specific Brands: This auto diagnostic scanner supports advanced ECU coding for specific european vehicles for VW, for Audi, for Skoda, for Mercedes-Benz, for Mitsubishi. It also enables ecu coding for BMW, for Volkswagen, for Jaguar, and for Land Rover. From coding and component matching to adaptive data resets, this scan tool helps you flash hidden features and match components after repairs or replacements. Note: ECU coding functionality varies by vehicle and module, please check the compatibility before order.
OE All-System Diagnostics & 8-in-One Data Graphing: With full system diagnostics, the VD70 automotive diagnostic scanner covers essential vehicle systems such as Engine, Transmission, ABS, Airbags, Brake, Chassis, and more. It allows you to read/clear codes, access ECU information, view live data streams. You can export data as CSV, record/playback data, view freeze-frame data, and perform active tests and services-all with one car computer diagnostic tool. This comprehensive analysis helps pinpoint issues quickly, leading to more accurate repairs.
【A MUST-HAVE TOOL FOR DIYERS】 - VDIAGTOOL VD10 car code reader is an incredibly useful obd scanner for each car owner or hobbyist, even for those with little to no experience when it comes to vehicle mechanics! Similar to a fixd car diagnostic tool, using this car diagnostic scanner is extremely easy. All you have to do is attach it to your car OBDII port and you can diagnose car problems in seconds! Read Codes (DTCs); Clear Codes; Live Data; View Freeze Frame; I/M Readiness; Vehicle Information.
【KEEP ENGINE IN GOOD STATUS】 - VDIAGTOOL check engine code reader brings a fast access to scan, read the car fault code, show its definition on the screen instantly, troubleshooting to find the root causes of problems, erase the engine fault code and turn off the MIL (Malfunction Indicator Light). Similar to a fixd car diagnostic tool, this car code reader helps ensure your engine stays in top condition.
【READ/CLEAR CODES & DTC LOOKUP】- No search online & saving your time, this vehicle car code reader retrieves generic (P0, P2, P3, and U0), manufacturer specific (P1, P3, and U1) codes, pending codes and displays DTC definitions based on the built-in database(more than 3000 codes) on the TFT screen, find out the root causes and clear the codes after fixed.
【LIVE DATA & RETRIEVE FREEZE FRAME】 - This diagnostic scan tool for accurate diagnosis enables you to retrieve data from vehicle sensors, such as Engine RPM, Intake air temperature, Short/Long term fuel, Misfire data and etc. The freeze frame is stored in the PCM together with the diagnostic trouble code (DTC) related to the fault. Comparable to a fixd car diagnostic tool, the VD10 car code reader car scanner can be a valuable & practical diagnostic aid and also greatly help when diagnosing intermittent problems.
【I/M READINESS for THE S-nn-0-g CHECK】- OBDII vehicle may not pass the annual inspection unless the required monitors since reset are complete. So you should at least read the readiness monitors and make sure they are ready. This car obd2 scanner diagnostic tool is equipped with I/M readiness function to check the operations of the e-m-issi0n system on OBD2 compliant vehicles, run I/M monitor readiness test, checking if the pass vehicle s-m-0-g inspection.
【ENHANCED OBDII SCANNER DIAGNOSTIC TOOL】The VDIAGTOOL VD30 Pro performs all 10 essential OBD2 tests, making it a powerful alternative to tools like the FIXD car diagnostic tool. It can turn off the Check Engine Light (CEL), read/clear fault codes, display live data with 4-in-1 graphing, and access freeze frame data. Additional features include one-click I/M readiness (smog check), on-board monitor test (Mode 06), component test, O2 sensor test, vehicle info, and module present. Bonus functionalities such as voltage test, DTC lookup, data playback, and data printing make this a comprehensive tool. Get this car code reader today and save yourself time and a costly trip to the dealership!
【EASY TO USE】No steep learning curve here—this car code reader and reset tool boots up instantly, with clear menu prompts and one‑click scan. First‑time users will appreciate the straightforward interface: plug in, select “Scan,” and get fault codes and readiness status without extra steps or hidden menus. Compared to competing scanners with cryptic LEDs or tiny displays, VD30 Pro escaner automotriz full‑text feedback ensures you know exactly what to do next.
【RELIABLE PERFORMANCE LASTS FOR YEARS】Engineered with an upgraded processing chip and rugged, drop‑resistant housing, the VD30 Pro car diagnostic tool endures harsh garage and roadside conditions. While some scanners require frequent firmware downloads before first use, VD30 Pro escaner automotriz ships ready—and continues to receive lifetime free updates via USB on Windows. It’s the obd-ii scanner diagnostic tool that professionals and DIYers trust for longevity.
【ONE-CLICK SMO_G CHECK】 With a dedicated I/M Readiness hotkey, this check engine code reader with reset instantly shows emission monitor status on a single screen—no cycling through submenus. Whether you’re prepping for a state inspection or diagnosing a stubborn MIL, the VD30 Pro escaner automotriz makes it simpler and more efficient than scanners like the FIXD car diagnostic tool that rely on color‑coded LEDs or require external printers.
【DTC LOOKUP+VOLTAGE TEST+DATA REVIEW, PLAYBACK & PRINTING】Featuring a built‑in library of over 98,000 DTC definitions, this auto scanner diagnostic code scanner explains faults in plain English. The integrated battery voltage reading prevents no‑start surprises, while data review, playback, and print functions let you build service reports—far beyond basic code readers like the FIXD car diagnostic tool that stop at just showing “P0XXX.” Share professional‑grade reports with your mechanic or keep a log of your car’s health.
【Why VDIAGTOOL VD70 Lite is A Game Changer?】VDIAGTOOL VD70 Lite offers essential car inspection and repair features at a more affordable price(Under $300), including Full Bidirectional Controls, OE Factory Level All Systems Diagnostics, 31+ Hot Services, CAN FD & DoIP, Comprehensive Data Streaming Capabilities (Export as CSV, Recording, Playback, 8-in-One), 3-Year Software Update, etc. Perfect choice for DIYers, Car Owners, Technicians and Mechanics!
This product presentation was made with AAWP plugin.
Last update on 2025-05-13 / Affiliate links / Images from Amazon Product Advertising API
Loading...
Reload document 
Open in new tab S.p.A. informs you that a new baseline software update is now available. Solution for the field: Update the car as stated in the follow instructions. IMPORTANT! Before carrying out the operations contained in this bulletin, please execute any other campaigns planned for this vehicle in the time order in which they were issued. The time order can be identified by the name of the bulletin. Example: L62X-A04.19 is bulletin number 4 of 2019. Spare Parts: None The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of Automobili Lamborghini
S.p.A. informs you that a new baseline software update is now available.
Solution for the field:
Update the car as stated in the follow instructions.
IMPORTANT!
Before carrying out the operations contained in
this bulletin, please execute any other campaigns
planned for this vehicle in the time order in which
they were issued. The time order can be identified
by the name of the bulletin. Example: L62X-A04.19 is bulletin number 4 of 2019.
Spare Parts:
None
The procedures and information published herein are strictly confidential and are intended exclusively for recognized professionals and persons who are authorized to receive said information. All copyrights are the property of
Automobili 
