| “This site contains affiliate links for which OEMDTC may be compensated” |
August 18, 2021 NHTSA CAMPAIGN NUMBER: 21V647000
ESC Malfunction May Cause Loss of Vehicle Control
A malfunctioning ESC system can cause a loss of vehicle control, increasing the risk of a crash.
NHTSA Campaign Number: 21V647
Manufacturer Bentley Motors, Inc.
Components ELECTRONIC STABILITY CONTROL
Potential Number of Units Affected 28
Summary
Bentley Motors, Inc. (Bentley) is recalling certain 2021 Bentayga vehicles. Incorrect software for the chassis control module may cause the Electronic Stability Control (ESC) system to malfunction.
Remedy
Dealers will update the chassis control module with the correct software, free of charge. Owner notification letters were mailed on October 5, 2021. Owners may contact Bentley customer service at 1-800-777-6923. Bentley’s number for this recall is Re21/31.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
RECALL CAMPAIGN – Bentley Bentayga V8 Chassis Control Module update (RE21/29)
This letter is to initiate a recall campaign to update the software parameters of the Chassis Control Module on certain Bentayga V8 vehicles fitted with standard (passive) roll bars and manufactured in June 2021.
This letter will provide you with all of the information to explain why this recall is being initiated, the actions you are required to take and provide you with the appropriate administrative details.
As part of an internal testing programme, it was identified that incorrect software parameters have been released for the Chassis Control Module of certain customer vehicles. The designated software parameters were intended for vehicles with active roll bars only, however, were also released onto vehicles fitted with standard (passive) roll bars.
Drivers of the vehicle may notice increased vehicle body movement and/or increased vehicle pitch under certain driving conditions. During intense dynamic driving, such as evasive collision avoidance manoeuvres, where the vehicle is heavily loaded (e.g. fully laden boot or roof box), there is a risk of late Electronic Stability Control (ESC) intervention, which could result in a loss of vehicle control.
Attached is a Bentley Technical Product Information (TPI) document, which lists the affected VINs and details the procedure which must be followed exactly. This software update is available now.
Every affected inventory vehicle must be REMEDIED BEFORE DELIVERY TO CONSUMERS. Therefore, please carry out following Stop Sale/Stop Delivery immediately.
IMPORTANT REMINDER: VEHICLES AFFECTED BY SAFETY & COMPLIANCE RECALLS
IT IS A VIOLATION OF FEDERAL LAW FOR DEALERS TO DELIVER TO CUSTOMERS NEW VEHICLES IN THEIR INVENTORY AFFECTED BY THIS NOTIFICATION UNTIL THESE VEHICLES ARE REMEDIED.
DEALERS SHOULD NOT SELL, LEASE, RENT, OR LOAN ANY NEW OR USED VEHICLES IN DEALER INVENTORY AFFECTED BY THIS NOTIFICATION PRIOR TO REMEDY. DEALERS GROUNDING LEASE RETURNS SHOULD REMEDY ALL AFFECTED GROUNDED VEHICLES.
Ensure all relevant dealership personnel are aware of this notice so they are able to address customer questions. Contact your ASM if you require additional assistance. Please direct press inquiries to Erin Bronner at erin.bronner@bentley-usa.com.
Owners of affected cars will be notified in writing week beginning September 27th 2021
It is not necessary to contact us for authorisation. We will take our records from your warranty claim which must be generated and submitted immediately upon completion of the work. You are reminded that claims for recalls cannot contain any other warranty repairs. The warranty code and repair time are quoted within the TPI.
It is to our mutual advantage that this recall campaign goes as smoothly as possible. Should you have any questions or queries concerning this recall, please contact your Area Service Manager or myself.
Technical background
Incorrect software parameters have been released for the Chassis control module of certain vehicles. The designated software parameters were intended for vehicles with active roll bars only, however, this was also released onto vehicles fitted with standard (passive) roll bars.
Remedy
Latest specification software should be applied to address 74 – Chassis control module
Customer notification
Customers of affected vehicles will be notified in writing by their Bentley retailer to arrange an appointment, make a note of the required action on the workshop order before it is signed by the customer
If it is omitted to perform the work required during a workshop visit, the customer should be notified immediately
You should also pass on this information to your new and used car sales departments so that affected vehicles are checked and repaired immediately
Genuine parts
Not applicable
Parts supply
Not applicable
Parts despatch control
Not applicable
Questions and answers
1) What is the specific issue with the affected vehicles?
The incorrect software parameters have been released for the Chassis Control Module of certain customer vehicles. The designated software parameters were intended for vehicles with active roll bars only, however, this was also released onto vehicles fitted with standard (passive) roll bars.
2) What repercussions does the fault have?
Drivers of the vehicle may notice increased vehicle body movement and/or increased vehicle pitch under certain driving conditions. During intense dynamic driving, such as evasive collision avoidance manoeuvres, where the vehicle is heavily loaded (e.g. fully laden boot or roof box), there is a risk of late Electronic Stability Control (ESC) intervention, which could result in a loss of vehicle control.
3) Which vehicles are affected?
21MY Bentayga V8 vehicles fitted with standard roll bars only and built between 9th and 29th June 2021.
4) Can customers continue to drive the cars?
Yes, they can continue to use the vehicle, however, we encourage customers to apply extra caution until the vehicle has been modified.
5) What is the fix?
Bentley authorised retailers will update the Chassis Control Module with the correct software parameters. This procedure will be carried out free of charge and will take approximately thirty minutes.
6) Do I have to make an appointment?
Yes, that’s important. Please contact your retailer immediately.
Technical background
Incorrect software parameters have been released for the Chassis control module of certain vehicles. The designated software parameters were intended for vehicles with active roll bars only, however, this was also released onto vehicles fitted with standard (passive) roll bars.
Check
If the vehicle is not already listed as repaired in the “Repair history” (in Elsa Pro) refer to the Identification section and check for the yellow paint mark on the front anti roll bar (right hand side) as shown in the Identification section
Should neither be evident (“Repair history” or applicable paint mark) carry out the required work in accordance with these instructions
Genuine parts
Not applicable
Work
General information for the reprogramming:
- The closed-circuit voltage of the vehicle must be at least 12.5 V during the reprogramming. Connect the battery of the vehicle to an external power supply. For further information see the Maintenance manual.
- During the reprogramming switch off all unnecessary consumers (ventilation, seat heater, interior lights).
- Because of the highest transmission stability we recommend the use of the diagnosis interface VAS 6154 (WiFi diagnostic tool) only in the USB operation or the cable-connected VAS 5055 for the reprogramming (updating) of control units. If these units are not available, the diagnosis interface VAS 5054 (A) can also be used in USB mode
The vehicle MUST be removed from Transport and Loading Mode before conducting this procedure
- Select and run Guided fault finding
- Within the Special functions tab select SVM – Code Input
- Select Perform test (Figure 1)
- On the next screen enter the SVM code 4V074ML01 and select Adopt (Figure 2).
- Follow all on screen prompts
- All control modules will now be interrogated.
- Once this is complete, a confirmation message will be evident confirming that the all actions have been completed successfully
- Select Done/Continue
- Follow on screen prompts until program end
- Clear all DTC’s before conducting the remaining steps
- On completion of steps 1 through to 3, carry out the remaining instructions to completion:
- Using ODIS – Carry out the test Axle Load Sequence Basic Settings test to completion. NOTE: This test can be found under Special Functions VERY IMPORTANT: ensure all instructions are strictly followed including all warnings/care points
- On completion clear all DTCs
- After the update programming, gear selection will not be possible. To wake up the system a bus silence is required, carry out the following steps in the order stated below:
- Switch off the ignition
- Remove the diagnostic interface from the OBD port
- Switch off and remove the battery charger from the vehicle
- Close the bonnet and all doors then lock the vehicle
- Wait 5 minutes so that the vehicle goes into bus silence
- When 5 minutes has elapsed, unlock the vehicle and open the driver’s door
- Switch on the ignition
- Confirm that the gear selection is now possible
- Place a yellow paint mark on the front anti roll bar (right hand side) as shown in the Identification section
Identification
Repair instructions Notes
SEOCONTENT-START
Aftersales
21-050
To: Parts & Service
Subject:
August 27, 2021
Bentley Bulletin
RECALL CAMPAIGN – Bentley Bentayga V8 Chassis Control Module update
(RE21/29)
Bentley Motors, Inc., 2003 Edmund Halley Drive, Reston, VA 20191 Page 1 of 2
RECALL CAMPAIGN – Bentley Bentayga V8 Chassis Control Module update (RE21/29) This letter is to initiate a recall campaign to update the software parameters of the Chassis Control Module on certain Bentayga V8 vehicles fitted with standard (passive) roll bars and manufactured in June 2021. This letter will provide you with all of the information to explain why this recall is being initiated, the actions you are required to take and provide you with the appropriate administrative details. As part of an internal testing programme, it was identified that incorrect software parameters have been released for the Chassis Control Module of certain customer vehicles. The designated software parameters were intended for vehicles with active roll bars only, however, were also released onto vehicles fitted with standard (passive) roll bars. Drivers of the vehicle may notice increased vehicle body movement and/or increased vehicle pitch under certain driving conditions. During intense dynamic driving, such as evasive collision avoidance manoeuvres, where the vehicle is heavily loaded (e.g. fully laden boot or roof box), there is a risk of late Electronic Stability Control (ESC) intervention, which could result in a loss of vehicle control. Attached is a Bentley Technical Product Information (TPI) document, which lists the affected VINs and details the procedure which must be followed exactly. This software update is available now. Every affected inventory vehicle must be REMEDIED BEFORE DELIVERY TO CONSUMERS. Therefore, please carry out following Stop Sale/Stop Delivery immediately.
IMPORTANT REMINDER: VEHICLES AFFECTED BY SAFETY & COMPLIANCE RECALLS
IT IS A VIOLATION OF FEDERAL LAW FOR DEALERS TO DELIVER TO CUSTOMERS NEW VEHICLES IN THEIR INVENTORY AFFECTED BY THIS NOTIFICATION UNTIL THESE VEHICLES ARE REMEDIED.
DEALERS SHOULD NOT SELL, LEASE, RENT, OR LOAN ANY NEW OR USED VEHICLES IN DEALER INVENTORY AFFECTED BY THIS NOTIFICATION PRIOR TO REMEDY. DEALERS GROUNDING LEASE RETURNS SHOULD REMEDY ALL AFFECTED GROUNDED VEHICLES.
Aftersales
21-050
To: Parts & Service
Subject:
August 27, 2021
Bentley Bulletin
RECALL CAMPAIGN – Bentley Bentayga V8 Chassis Control Module update
(RE21/29)
Bentley Motors, Inc., 2003 Edmund Halley Drive, Reston, VA 20191 Page 2 of 2
Ensure all relevant dealership personnel are aware of this notice so they are able to address customer questions. Contact your ASM if you require additional assistance. Please direct press inquiries to Erin Bronner at erin.bronner@bentley-usa.com.
Owners of affected cars will be notified in writing week beginning September 27th 2021
It is not necessary to contact us for authorisation. We will take our records from your warranty claim which must be generated and submitted immediately upon completion of the work. You are reminded that claims for recalls cannot contain any other warranty repairs. The warranty code and repair time are quoted within the TPI.
It is to our mutual advantage that this recall campaign goes as smoothly as possible. Should you have any questions or queries concerning this recall, please contact your Area Service Manager or myself.
Sincerely,
Stephen Worrall
Director, Aftersales
Field campaign
Topic
Bentley Bentayga V8 Chassis Control Module update (RE21/29)
Market area
Russische Föderation (5RU),Australia E04 Bentley rest Asia and Australia (6E04),Germany E02 Bentley rest Europe (6E02),United Arab Emirates E06 Bentley Middle East and Africa (6E06),United Kingdom E01 Bentley UK (6E01),United States E05 Bentley USA and rest America (6E05)
Brand
Bentley
Transaction No.
2064207/1
Campaign number
RC11
Note
Type
US code
Vehicle data
Bentayga V8 Kovomo
Sales types
Type
MY
Brand
Designation
Engine code
Gearbox code
Final drive code
4V14D9
2021
E
*
*
*
Chas is numbers
Manufacturer
Filler
Type
Filler
MY
Factory
From
To
Prod from
Prod to
SJA
A53
4V
8
M
C
037798
037798
SJA
AM4
ZV
1
M
C
037773
037773
SJA
AM2
ZV
5
M
C
037778
037778
SJA
AM2
ZV
0
M
C
037946
037946
SJA
AM2
ZV
2
M
C
038063
038063
SJA
AM2
ZV
X
M
C
037758
037758
SJA
AM2
ZV
3
M
C
037763
037763
SJA
AM2
ZV
4
M
C
037853
037853
SJA
AM2
ZV
2
M
C
037737
037737
SJA
AM2
ZV
X
M
C
037906
037906
SJA
AM2
ZV
0
M
C
038028
038028
SJA
AM2
ZV
6
M
C
038034
038034
SJA
AM2
ZV
6
M
C
038101
038101
SJA
AM2
ZV
0
M
C
037834
037834
SJA
AM2
ZV
9
M
C
037914
037914
SJA
AM2
ZV
X
M
C
037985
037985
SJA
AM2
ZV
3
M
C
037827
037827
SJA
AM2
ZV
4
M
C
038033
038033
SJA
AM2
ZV
0
M
C
037736
037736
SJA
AM2
ZV
6
M
C
037966
037966
SJA
AM2
ZV
6
M
C
037823
037823
SJA
AM2
ZV
6
M
C
037921
037921
SJA
AM2
ZV
7
M
C
038107
038107
SJA
AM2
ZV
5
M
C
037876
037876
SJA
AM2
ZV
2
M
C
037950
037950
SJA
AM2
ZV
9
M
C
037900
037900
SJA
AM2
ZV
X
M
C
037923
037923
SJA
AM2
ZV
X
M
C
037811
037811
SJA
AM2
ZV
5
M
C
037862
037862
SJA
AM2
ZV
7
M
C
037765
037765
SJA
AM2
ZV
9
M
C
038030
038030
SJA
AM2
ZV
4
M
C
037934
037934
SJA
AL3
4V
0
M
C
037963
037963
SJA
AL1
4V
9
M
C
038064
038064
SJA
AB1
4V
X
M
C
038061
038061
SJA
AL1
4V
1
M
C
037734
037734
SJA
AL1
4V
3
M
C
037847
037847
SJA
AL1
4V
6
M
C
037972
037972
SJA
A51
4V
9
M
C
037748
037748
SJA
A51
4V
3
M
C
037857
037857
SJA
A51
4V
3
M
C
037888
037888
SJA
A51
4V
4
M
C
037740
037740
SJA
A51
4V
9
M
C
037751
037751
SJA
A51
4V
1
M
C
038067
038067
SJA
A51
4V
X
M
C
037810
037810
SJA
A51
4V
1
M
C
037887
037887
SJA
AL1
4V
9
M
C
037755
037755
SJA
AL1
4V
7
M
C
037916
037916
SJA
A51
4V
2
M
C
037753
037753
SJA
AL1
4V
4
M
C
037940
037940
SJA
AL1
ZV
4
M
C
037767
037767
SJA
AL1
ZV
3
M
C
037808
037808
SJA
AL1
ZV
6
M
C
037818
037818
SJA
AL1
ZV
9
M
C
037828
037828
SJA
AL1
ZV
7
M
C
037861
037861
SJA
AL1
ZV
3
M
C
037730
037730
SJA
AL1
ZV
8
M
C
037870
037870
SJA
AL1
ZV
7
M
C
037830
037830
SJA
AL1
ZV
9
M
C
037733
037733
SJA
AL1
ZV
3
M
C
037825
037825
SJA
AL1
ZV
9
M
C
037991
037991
SJA
AL1
ZV
5
M
C
038068
038068
SJA
A51
4V
4
M
C
037897
037897
SJA
A51
4V
4
M
C
037902
037902
SJA
AM2
ZV
9
M
C
037749
037749
Documents
Document name
master.xml
Notes Repair instructions
Technical background
Incorrect software parameters have been released for the Chassis control module of certain vehicles. The designated software parameters were intended for vehicles with active roll bars only, however, this was also released onto vehicles fitted with standard (passive) roll bars.
Remedy
Latest specification software should be applied to address 74 – Chassis control module
Customer notification
Customers of affected vehicles will be notified in writing by their Bentley retailer to arrange an appointment, make a note of the required action on the workshop order before it is signed by the customer
If it is omitted to perform the work required during a workshop visit, the customer should be notified immediately
You should also pass on this information to your new and used car sales departments so that affected vehicles are checked and repaired immediately
Warranty accounting instructions Warranty type 710 or 790 Damage service number RC11
Damage code 00 99
Labour
Labour operation code 01 51 00 00
Time As per the ODIS log (Must not exceed 50 time units)
Criteria 01
Genuine parts
Not applicable
Parts supply
Not applicable
Parts despatch control
Not applicable
Questions and answers
1) What is the specific issue with the affected vehicles?
The incorrect software parameters have been released for the Chassis Control Module of certain customer vehicles. The designated software parameters were intended for vehicles with active roll bars only, however, this was also released onto vehicles fitted with standard (passive) roll bars.
2) What repercussions does the fault have?
Drivers of the vehicle may notice increased vehicle body movement and/or increased vehicle pitch under certain driving conditions. During intense dynamic driving, such as evasive collision avoidance manoeuvres, where the vehicle is heavily loaded (e.g. fully laden boot or roof box), there is a risk of late Electronic Stability Control (ESC) intervention, which could result in a loss of vehicle control.
3) Which vehicles are affected?
21MY Bentayga V8 vehicles fitted with standard roll bars only and built between 9th and 29th June 2021.
4) Can customers continue to drive the cars?
Yes, they can continue to use the vehicle, however, we encourage customers to apply extra caution until the vehicle has been modified.
5) What is the fix?
Bentley authorised retailers will update the Chassis Control Module with the correct software parameters. This procedure will be carried out free of charge and will take approximately thirty minutes.
6) Do I have to make an appointment?
Yes, that’s important. Please contact your retailer immediately.
RC11
Bentley Bentayga V8 Chassis Control Module update (RE21/29)
Transaction No.: 2064207/1
Repair instructions Notes
Technical background
Incorrect software parameters have been released for the Chassis control module of certain vehicles. The designated software parameters were intended for vehicles with active roll bars only, however, this was also released onto vehicles fitted with standard (passive) roll bars.
Check
If the vehicle is not already listed as repaired in the “Repair history” (in Elsa Pro) refer to the Identification section and check for the yellow paint mark on the front anti roll bar (right hand side) as shown in the Identification section
Should neither be evident (“Repair history” or applicable paint mark) carry out the required work in accordance with these instructions
Genuine parts
Not applicable
Work
General information for the reprogramming:
• The closed-circuit voltage of the vehicle must be at least 12.5 V during the reprogramming. Connect the battery of the vehicle to an external power supply. For further information see the Maintenance manual.
• During the reprogramming switch off all unnecessary consumers (ventilation, seat heater, interior lights).
• Because of the highest transmission stability we recommend the use of the diagnosis interface VAS 6154 (WiFi diagnostic tool) only in the USB operation or the cable-connected VAS 5055 for the reprogramming (updating) of control units. If these units are not available, the diagnosis interface VAS 5054 (A) can also be used in USB mode
The vehicle MUST be removed from Transport and Loading Mode before conducting this procedure
1. Select and run Guided fault finding
• Within the Special functions tab select SVM – Code Input
• Select Perform test (Figure 1)
Figure 1
2. On the next screen enter the SVM code 4V074ML01 and select Adopt (Figure 2).
• Follow all on screen prompts
Figure 2
• All control modules will now be interrogated.
3. Once this is complete, a confirmation message will be evident confirming that the all actions have been completed successfully
• Select Done/Continue
• Follow on screen prompts until program end
• Clear all DTC’s before conducting the remaining steps
4. On completion of steps 1 through to 3, carry out the remaining instructions to completion:
• Using ODIS – Carry out the test Axle Load Sequence Basic Settings test to completion. NOTE: This test can be found under Special Functions VERY IMPORTANT: ensure all instructions are strictly followed including all warnings/care points
• On completion clear all DTCs
5. After the update programming, gear selection will not be possible. To wake up the system a bus silence is required, carry out the following steps in the order stated below:
• Switch off the ignition
• Remove the diagnostic interface from the OBD port
• Switch off and remove the battery charger from the vehicle
• Close the bonnet and all doors then lock the vehicle
• Wait 5 minutes so that the vehicle goes into bus silence
• When 5 minutes has elapsed, unlock the vehicle and open the driver’s door
• Switch on the ignition
• Confirm that the gear selection is now possible
6. Place a yellow paint mark on the front anti roll bar (right hand side) as shown in the Identification section
Identification
Repair instructions Notes**************************************************************************************************************BENTLEY MOTORS, INC. 2003 Edmund Halley Drive, Reston, VA 20191, U.S.A. Telephone: (800) 777 6923 / Fax: (248) 754 6541 www.bentleymotors.com IMPORTANT SAFETY RECALL Name Address Address Model Year/Model: <> NHTSA: 21V647 RE: SAFETY RECALL – ELECTRONIC STABILITY CONTROL MODULE SOFTWARE This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. Bentley Motors has decided that a defect, which relates to motor vehicle safety, exists in certain 2021 model year Bentley Bentayga vehicles. Our records show that you are the owner of one of these vehicles. What is the issue Some chassis control modules have had incorrect software installed which may cause the Electronic Stability Control (ESC) system to malfunction. In high-dynamic driving situations (such as in an evasive collision avoidance maneuver) there is a risk of late ESC intervention which can cause a loss of vehicle control, increasing the risk of a crash. What will we do? To correct this defect, your authorized Bentley dealer will update the software for the chassis control module. This work will take about one hour to complete and will be performed for you free of charge. What should you do? Please telephone your authorized Bentley dealer without delay to schedule a repair appointment. Your dealer has all the necessary instructions to perform this important safety repair to your satisfaction. This notice applies to your vehicle, Vehicle Identification Number (VIN): OCTOBER 2021 DD eeaarr 2021 BENTAYGA V8 IMPORTANT SAFETY RECALL Precautions you should take If this condition is present in the vehicle, the driver may notice increased vehicle body roll and /or increased vehicle pitch. Should this occur, owners are advised to contact an authorized Bentley dealer without delay and make arrangements to have the vehicle diagnosed. Lease vehicles If you are the lessor and registered owner of the vehicle identified in this action, the law requires you to forward this letter immediately via first-class mail to the lessee within ten (10) days of receipt. Can we assist you further? If you have any questions, require any assistance or if you would like us to address any concerns that you may have, please telephone our dedicated Customer Service team at 1 800-777-6923. In the event your authorized Bentley dealer fails or is unable to remedy the defect free of charge within a reasonable time, you may also submit a complaint to: The Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, SE., Washington, DC 20590; or call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153); or go to https://www.nhtsa.gov. We would like you to know that we sincerely appreciate your continued support of our vehicles. I do apologize for the fact that we have to ask you to allow us to recall your vehicle for this modification. Yours Sincerely, Stephen Worrall Director, Aftersales IMPORTANT SAFETY RECALL
SEOCONTENT-END
1 Affected Product
Vehicle
| MAKE | MODEL | YEAR |
| BENTLEY | BENTAYGA | 2021 |
7 Associated Documents
Manufacturer Notices(to Dealers,etc) – Safety Bulletin re RECALL CAMPAIGN Bentley Bentayga V8 Chassis Control Module update (RE21/29)
RCMN-21V647-6841.pdf 941.807KB
Loading...
Reload document 
Open in new tab
Recall Acknowledgement
Loading...
Defect Notice 573 Report
RCLRPT-21V647-6399.PDF 215.517KB
Loading...
ISSUED Owner Notification Letter(Part 577)
RCONL-21V647-9472.pdf 256.902KB
Loading...
Recall Quarterly Report #1, 2021-4
RCLQRT-21V647-4057.PDF 211.141KB
Loading...
Remedy Instructions and TSB
RCRIT-21V647-7425.pdf 340.493KB
Loading...
Recall Quarterly Report #2, 2022-1
RCLQRT-21V647-1881.PDF 211.238KB
Loading...
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=21V647&docType=RCL
- 5 IN 1 DIAGNOSTIC SCANNER: This is an OBDII scanner and 4 systems diagnostic tool. The AUTOPHIX 3210 PRO Bluetooth Auto Scanner not only has OBDII diagnostic function, but can also be used as an ABS/SRS/transmission scanner and check engine code reader. When it is an OBD2 scanner, you can use it to check if your car is ready for annual test via I/M preparation menu. In addition, the built-in DTC library, live data stream, data playback, performance testing and many more such functions are supported by it.
- RELIABLE CAR HEALTH MONITOR: Are you confused when the ABS/SRS/Transmission/Check Engine warning light is blinking? The AUTOPHIX 3210 PRO Bluetooth Scanner will help you to do a thorough scanning and inspecting of your car and find out the root cause, which saves your time and money. Tip:The warning light will be turned off after the problem is solved. Airbag crash/collision data cannot be cleared, even if you replace the airbag with a new one.
- QUICK DIAGNOSIS: The 3210 PRO is the newest 2024 Enhanced 4-System Bluetooth Code Reader that retrieves vehicle information, reads/clears trouble codes, and displays a 4-in-1 live data stream. You'll easily find out what's wrong with your car. In just a few minutes, you'll be in control of your car!
- EXCLUSIVE APP: Are you tired of the following with third party apps? For example: 1.need to download different apps for different cars? 2. require extra download fees? 3. only support a few functions? 4. can only use one of Android and iOS? Now!One AUTOPHIX 3210 PRO Scanner is enough to solve all the above problems. The must-have wireless/bluetooth automotive diagnostic tool/code reader for today's car owners. iPhone iOS, iPad, Android can be downloaded for free without any additional subscription fees.
- ADVANCED DATA FLOW DISPLAY:AUTOPHIX 3210 PRO Bluetooth code reader allows you to graphically display your vehicle's data flow instead of boring text, including engine coolant temperature, engine RPM, vehicle speed, absolute throttle position, control module voltage, etc. You can view different parameter values corresponding to different times. The advanced data streams provide useful information for entry-level professionals and diyers who can troubleshoot vehicle problems quickly and efficiently.
- 🎄【Easy to Use--Work out of box】+【FOXWELL 2024 New Version】 FOXWELL NT604 Elite scan tool is the 2024 new version from FOXWELL, which is designed for those car owners who want to figure out the cause issue before fixing the car problem via scanning the most common systems like abs srs engine and transmission.The NT604 Elite diagnostic tool comes with latest software, which can be used out of box. No need to waste time to download the software first.
- 🎅【Affordable】+【Reliable Car Health Monitor】 Will you be confused what happen when the warning light of abs/srs/transmission/check engine flashes? Instead of taking your cars to dealership, this foxwell scanner will help you do a thorough scanning and detection for your cars and pinpoint the root cause. It will t-urn off the warning light car after the problem is fixed.👉TIPS: Airbag crash/collision data can NOT be cleared even you replace the new airbag.
- 🎄【5 in 1 Diagnostic Scanner】Compared with those auto scanners (50-100), NT604 Elite code scanner not only includes their OBDII diagnosis but also it can be an abs/srs scanner, transmission and check engine code reader. When it’s an odb2 scanner, you can use it to check if your car is ready for annual test through I/M readiness menu. In addition, live data stream, built-in DTC library, data play back and print, all these features are a big plus for it.
- 🎅【Fantastic AUTOVIN】+【No extra software fee】Through the AUTOVIN menu, this NT604 Elite car scanner allows you to get your V-IN and vehicle info rapidly, no need to take time to find your V-IN and input one by one. What's more, the NT604 Elite abs srs scanner supports 60+ car makes from worldwide (America/Asia/Europe). You don’t need to pay extra software fee.
- 🎄【Solid protective case KO plastic carrying bag】+ 【Lifetime update】Almost all same price-level obd scanner diagnostic tool only offers plastic bag to hold on the scanner.However, NT604 Elite automotive scanner is equipped with solid protective case, preventing your obd2 scanner from damage. Then you don’t need to pay extra money to buy a solid toolbox.
- 🎉【2024 Upgraded Ver. of AL519/ ML519/ ML619】Autel develops the brand-new AutoLink AL619 as the advanced ver. of Autel ML519, AL519, AL319, MS309. This AL619 OBD2 scanner can scan ABS & SRS systems, and support 10 Modes of OBD II Diagnostics Function on Worldwide Vehicles to read, erase codes and turn off the MIL, ABS, SRS warning lights so that you can better maintain your car when related malfunctions occur and make your vehicle ready for the annual test.
- 🎉【Accurate ABS/ SRS Diagnostics Functions】The ABS/ SRS diagnostic function is used to retrieve and clear codes from the ABS/ SRS systems. It can read and clear DTCs, show definitions of each code, display live data of multiple sensors in the graph to locate fault causes, and assist home mechanics to do the proper repair and clear ABS & Airbag warning lights. Diagnoses ABS/ SRS system codes on most 1996 and newer major vehicle models. Please email 📩 immoautel @ outlook. com 📩 for help.
- 🎉【All 10 Modes of OBD II Diagnostics Function】The OBD II Diagnostics function is a fast-access option that allows you to carry out a quick test on the engine system of OBD II vehicles. Read Codes, Erase Codes, Live Data, Freeze Frame, Retrieving I/M Readiness Status, O2 Monitor Test, On-Board Monitor Test, DTC Lookup, Component Test, Viewing Vehicle Information, Modules Present.
- 🎉【Live Data and Freeze Frame Data】With Live Data functions, Autel AL619 OBD2 diagnostic code reader allows you to view the live PID (Parameter Identification Data) of the vehicle's computer module(s) in text, graph to check the status of various sensors. And Freeze Frame Data enables you to view the vehicle's operating parameters at the moment a DTC is detected. These information will aid the technician by allowing the parameters to be duplicated for diagnostic and repair purposes.
- 🎉【DTC Lookup Feature】Besides showing you the code’s definition while you are reading the diagnostic trouble codes, AL619 features comparably user-friendly DTC Lookup Function which enables you to retrieve the definitions of any error codes from the large database of AL619, saving you from the hassle of wasting time searching definition of every code via Google.
- 2024 Best Choice for ABS Bleeder Scan Tool - Was the brake pedal always slowly sinking down or becoming loose? This abs brake bleeding scan tool will bleed the brake system by cycling the pump and valves to achieve a tight brake pedal. It's the most affordable obd2 scanner with abs auto bleed function you can find. With the clear step by step instruction, even a beginner can use it. Coverage check on FOXWELL official site: Support- Diagnostic Coverage List.
- More Than a Entry Level OBD Scanner, Ideal for Home Mechanics - Based on the NT301 FOXWELL Scanner, NT630 Plus takes OBD diagnostics to the next level by customizing all functions for ABS and SRS systems. This srs abs scanner provides in-depth insights on error code diagnosis, wheel speed sensor live data, airbag circuits and cable connectors monitor, module activation and etc. It's an total game-changer in resolving ABS SRS issues.
- No More Higher End Service than You Needed - One NT630 Plus is enough! This obd2 scanner with abs and srs takes depth diagnosis on Anti-Lock Brake System & Supplemental Restraint System, and also performs daily required resetting services which same priced scanners cannot do. Like Airbag light reset/ SAS(Steering Angle Sensor) adjustment/ Oil light reset and EPB service functions. this car scanner will help the part to operate normally after the faults repaired.
- Also can Work like NT301 - The NT630 Plus abs code reader connect to the OBD2 port directly. It will diagnose all obd2 modules instantly, displays the live data, locates bad sensors and I/M readiness status before the annual inspection. Guides you to do the maintenance work, reduces the potential driving risk and keep a peak performance on the road.
- Complicate? Unreadable? - Intuitive LCD display with clear operate instructions, even a beginner can diagnose the car faults with the NT630 Plus. Ergonomic Touch with anti-collision and anti-slip cover design, comfortable for daily car diagnose work. Unique button press sound will provide the overall tactile and visual experience to notice you a task has been completed or a command has been executed.
- 💻Note: (About UPDATE) ANCEL FX2000 car scanner diasgnostic tool can be used directly as it comes with existed software, You don't need to register or update beforethe first use. It's recommended to update your scanner only when it fails to work on your car, or it's slow to load all menus or if you need newer software version. 📢Software update supports WIN XP, 7, 8, 10 operation systems only., but not for Mac and ios system.
- 🔧【PLUG AND PLAY - EASY TO USE】 : ANCEL FX2000 car scanner only takes 3 steps to connect to the car for diagnosis without cumbersome operations. The latest FX2000 scan tool is equipped with a one-key diagnosis function, which can automatically identify the model and year of your car, and automatically diagnose the car. Even beginners can use it to read the data and find out what the fault codes mean.
- 🚗【FULL OBD-LEVEL DIAGNOSTICS TOOL】: Quickly determines the cause of engine system faults, reads current, permanent and pending codes. After the repair, clears the codes and turns off the warning light. In addition, the FX2000 engine code reader also displays important OBD II advanced data such as fuel, live data and other manufacturer-specific parameters in real time to ensure that the engine ECU is operating correctly and safely, saving vehicle owners a lot of time and money in maintenance.
- 🚙【TRANSMISSION FAULT DIAGNOSTIC TOOL】: Some noises come from the transmission? Ancel obd2 scanner will read fault codes, display live transmission system data (fluid temperature, fluid pump, clutch actuation, pressure, etc.), and ensures transmission performance is optimal for vehicle speed and load. It provides detailed TCM data of the vehicle, so you can quickly and accurately find existing or potential problems.
- 🚐【FIND OUT SRS WRONG】: ANCEL FX2000 automotive scanner is able to read and clear fault codes in the SRS (airbag) and turn off the warning light to make sure the system is working correctly and safely. This odb2 scanner also displays a live graphical data stream of the supplemental restraint system (air bag), which allows you to analyze and verify that the air bag system is working properly.
- 【Buy with Confidence】 As a America's No.1 diagnostic tool brand, Innova stands for innovation, quality, and accessibility in the automotive diagnostic industry. We are known for developing cutting-edge diagnostic tools that are user-friendly, reliable, and made for US by Americans.
- 【Unleash Your Drive's Potential】Much more than a car code reader, the 6100P scanner effectively reads and erases engine, ABS, SRS, and transmission codes for popular US car makes such as Ford, Chevy, Dodge, GM, etc. When the traction light is constantly on, the ability to really detect where the problem is concerning brakes and airbags enables you to make sure all safety measures in place before putting yourself in harm's way.
- 【Your Car's Health Doctor】Easily view procedures or send commands for oil change, mileage or driving time reset for most 1996 and newer OBD2 vehicles. It also monitors your oil level and oil life status, ensuring optimal vehicle health.
- 【alternator Test】The Innova 6100P scanner is perfect for assessing the performance of the alternator in your hybrid, car, SUV, minivan, or light truck diesel as well. During rough winters and scorching summers, this diagnostic tool will be invaluable when trying to root out start-up issues.
- 【Drive with Confidence and Peace】Quickly identify if your vehicle needs immediate attention with our Code Severity Levels function. This feature helps you understand whether you need to fix an issue immediately or if it can wait until you get home, keeping warning lights at bay.
- [Transform Your Car Care Experience] - With BLCKTEC, instantly become your own professional mechanic. Effortlessly read and clear your car’s trouble codes and check engine light, ensuring your vehicle stays in top condition.
- [Empower Yourself with Comprehensive Diagnostics] - Unlock the full potential of your vehicle with the BLCKTEC 430. Access detailed diagnostics previously exclusive to professional mechanics’ OBD2 scan tools, including ABS, Airbag, SRS, TPMS codes, and beyond, right at your fingertips.
- [Drive with Confidence] - The BLCKTEC 430 is more than just a car code reader; it's your personal vehicle health advisor. Receive tailored repair reports with potential causes and verified solutions for your specific make and model, guiding you to the right fix every time.
- [Seamless Connectivity, Ultimate Convenience] - Experience the freedom of wireless diagnostics with this portable car scanner. Easily connect via Bluetooth to our intuitive sensor, and enjoy all the functionalities of high-end scan tools without the clutter of wires, directly from your smartphone or tablet.
- [DIY Repairs Made Easy] - Navigate car maintenance with ease using our premium app. Access a vast library of easy-to-follow repair videos, guiding you through each step of the repair process, compatible with both iOS & Android devices.
- [ABS & SRS Scanner with Active Test] The ABS/ SRS diagnostic tool Read & clear DTCs, displays live data in a graph to locate the cause of faults and assists the home mechanic with repairs and clearing ABS and airbag warning lights. Active test sensors, valves or solenoids etc. and tracks any threats in real time. It is invaluable to have a diagnostic tool with Active Test feature that you will never find on similar ABS/ SRS scanners.
- 【3 HOP Reset Services 】Easy to set up 3 regular reset services for Oil Light, Battery Management System, and Steering Angle Position. With this obd2 scanner, you can reset the oil service light and reset pre-programmed mileage intervals for energy efficiency; adjust or reset the steering angle position to keep steering aligned; and clear the original low battery fault information. No need to leave home for shop-quality car maintenance.
- 【All OBD2 Test Modes 】 This ABS & SRS scan tool is also a full featured obd2 code reader, allowing a quick test of the engine system of OBD II vehicles, can Read/Clear engine light codes, Live Data, Freeze Frame, Retrieving I/M Readiness Status, O2 Monitor Test, On-Board Monitor Test, Evap Test, Read Vehicle Information, and help pass smog test for most post-1996 OBD2/CAN vehicles.
- [DTC LookUp Library] Can't read the code? Go to the DTC LookUp Library. The Topdon AL600 OBD2 scanner offers a wealth of code definitions so you don't have to look them up in a list or database, and the HELP function takes you to diagnostic tips for possible fixes, saving time searching for repair materials online. No other scan tool or code reader under $100 offers this level of assistance.
- [User-Oriented] You'll love the feel of this automotive scanner, with black rubber grips all around the outer edges for durability and to withstand accidental drops. With its easy access menu, you can operate all functions in minutes with just a few button presses. The 3-color LEDs give you a intuitive indication of the OBD2 test results in a second. 3 shortcut keys, one key to read/clear DTCs and a one-touch smoke status check make it easy to use even for beginners.
- 🔥【Easy to use and friendly】+【Faster diagnostic speed】 FOXWELL NT604 is the 2024 newest enhanced 4 system code reader, which is capable of reading/clearing fault codes, retrieving vehicle information and displaying 4-in-1 live data stream. You will easily find what's wrong with your car to avoid expensive trip to dealership. At the same time, this car scanner will directly tell you what the corresponding code means, avoiding the hassle of searching for information.
- 🛠【OBD2 Full Function】+【Check Engine/ABS/SRS/Transmission】 This scan tool will allow you to perform full OBDII diagnostic for all cars with OBDII protocols. You can use it to check if your car is ready for annual testing through the I/M Readiness menu. In addition, the device also has value-added functions such as real-time data flow, DTC Lookup, data playback, and printing. Turn off Check Engine/ABS/SRS/Transmission Light. Tips: the fault code can be only erased after the problem is fixed.
- 🚗【Cover 10000+ models ＆60+ Car Makes】 and 【AUTOVIN】 Compared with Other scanner which only supports 40 car makes, NT604 car diagnostic scanner for all cars contains more than 60 car brands and 10000+ cars for almost all OBDII cars sold worldwide like passenger car, SUVs, minivans, light-duty trucks, etc. produced by Asian, European, American with the supported year differing from 1996 to 2024. It allows you to get your VIN and vehicle info rapidly, no need to take time input one by one.
- 🛒【Battery Voltage Checker】+【Lifetime Free Update, No Subscription fee 】 It monitors the real-time voltage of the vehicle battery and displays it in graphical and textual form, informing you of the health status of the battery. Also monitor the health of your car. NT604 is equipped with the latest software directly, so you don't need to download a bunch of updated software after unboxing to use it. Lifetime no subscription fee for upgrading software.
- 🎁【Great festival Idea：Applicable for Many People】+【High End and Exquisite Protective Packaging】 Best one item for Dad, Husband, Boyfriend, Handy Men. Every car owner will need a 4 systems diagnostic scan tool! This code reader fits for home mechanic, DIY car owners, advanced hobbyiest, car dealer, auto repair shop, automotive engineer, diagnostic tech, automobile tech, individual. Apparently, this is the most economical scan tool for every mechanic.
- [OBD2 Scanner] The TOPDON OBD2 scanner performs all ENG/AT/SRS/ABS diagnostics with 4-in-1 graphic live data. 🚩It covers all OBD2 tests for 67 manufacturers and 10000+ model. It also features 5-second one-touch AutoVIN, 🚩a free one-touch lifetime upgrade through WiFi, library DTC, 12 languages, 🚩printable auto-generated report with email sharing, 🚩smooth Android 11.0, 32GB ROM, 🚩vivid 5-inch touchscreen, and up to 10 hours of battery life.
- [4 Car System Code Reader] The TOPDON OBD2 scanner accesses 4 systems: 🚩Engine/ABS/SRS/Transmission. It identifies the ECU version, pull DTCs with 4-in-1 graphic live data and DTC explanation to identify issues, erase DTCs to turn off the warning lights after repair (For cars made in 2005 and newer). In order to help you extend the lifespan of your vehicle while improving performance, this code reader also includes all obd2 test modes to solve the major concerns for all vehicles.
- [User-Oriented TOPDON OBD2 Scanner] With this scan tool's touchscreen and rubberized buttons, you may easily navigate through menus or process while following a logical path. With 32GB on-board memory, the scanner enables for the recording of several diagnostic reports, which can be shared via email and printed for review. Along with this, you can 🚩upgrade your software for free for lifetime with one-touch over Wi-Fi for that help update the features and expanding car coverage.
- [Multiple Functions] The Smart AutoVIN of this TOPDON OBD2 scanner keeps track of your manual selections for vehicle make, model, and year and directs you to the suitable diagnostics. 🚩Max 4 Live Data streams integrated for much easier data processing. Diagnostic feedback online with this diagnostic tool to help you get tough repair operations well-completed. Real-time car battery voltage monitoring identifies probable vehicle defects.
- [Wide Coverage] With its multilingual menu and 🚩coverage of 67 car brands and 10,000+ models spanning North America, Europe, and Asia (including Malaysia, India, and Iran), this car scanner is compatible with the majority of 1996 and newer OBDII compliant automobiles (EN, FR, ES, DE, IT, RU, PT, JP, KR). Before buying, make sure the OBD2 scanner is compatible with your vehicle. The package contains only a charging cable and not a power adapter.
Last update on 2024-04-11 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.