1995-1998 Altec A0442 Aerial Devices MAB770 Uncontrolled Boom Movement

“This site contains affiliate links for which OEMDTC may be compensated”

July 20, 2020 NHTSA CAMPAIGN NUMBER: 20V420000

Uncontrolled Boom Movement

Uncontrolled movement of the boom can increase the risk of injury.

 

NHTSA Campaign Number: 20V420

Manufacturer Altec Industries Inc.

Components EQUIPMENT

Potential Number of Units Affected 141

 

Summary

Altec Industries, Inc. (Altec) is recalling certain 1995-1998 Altec A0442 aerial devices. The boom lift hydraulic cylinder end gland may fail causing uncontrolled boom movement.

 

Remedy

Altec will notify owners, and instruct them to inspect the boom lift cylinders for an externally threaded head gland design. The customer will be instructed whether the unit can be used with restricted lower and/or upper boom articulation until the cylinder(s) are repaired or replaced, free of charge. The recall began September 14, 2020. Owners may contact Altec customer service at 1-877-462-5832. Altec’s number for this recall is MAB 770.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 


IMPORTANT SAFETY RECALL

This notice applies to your vehicle. See attached serial number list

 

NHTSA Safety Recall

No. 20V-420

 

September 4, 2020

 

Dear Altec Owner,

This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act, and Canada Motor Vehicle Safety Act.

 

Altec Industries, Inc. has decided that a defect which relates to motor vehicle safety exists in certain AO442/445 aerial devices. These units may have a hydraulic cylinder on the upper boom and/or lower boom that can fail. A failed cylinder can cause uncontrolled movement resulting in death or serious injury.

 

Refer to MAB 770 for the items covered under the warranty policy. Altec will supply, free of charge, new hydraulic cylinder(s) to correct this condition.

 

In order to determine if your unit is affected by MAB 770, compare the serial number of your unit with the list of affected units attached to the MAB. The repair can be performed by the customer or you may contact Altec at 1-877-GO-ALTEC (1-877-462-5832) for further assistance. The repair is expected to take up to 10 hours to complete.

 

At any time, you may contact Altec at 1-877 GO ALTEC (1-877-462-5832) with your unit’s serial number to determine if there are any other outstanding notices.

 

For US owners: after contacting Altec, if you are still not able to have the safety condition remedied without charge and within a reasonable time, you may submit a complaint to: Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue SE, Washington, DC 20590 or call toll-free 1-888-327-4236 (TTY: 1-800-424-9153) or  go to https://www.safercar.gov.

 

For Canadian Owners: if you are still not able to have the safety condition remedied by your dealer within a reasonable time, please contact Altec Customer Service at 1-877-GO-ALTEC (1-877-462-5832).

 

If you had this repair performed before you received this letter, you may be eligible to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this recall. If you have sold or retired the unit please call Altec at 1-877-GO-ALTEC (1-877-462-5832) so the records may be changed.

 

If you have leased this equipment to another person or company, you are required by Federal Law to forward a copy of this notice to the lessee by first class mail within ten (10) days of the receipt of this notice.

 

We are sorry to cause this inconvenience; however we are taking this action in the interest of your safety and continued satisfaction with Altec products.

 

Thank you for your immediate attention on this important matter.

 

MAB 770


September 4, 2020

Mandatory Action Bulletin

Units Affected: AO442/445 units built from 1995 to 1998 (please verify that your unit serial number is affected by reviewing the attached list in this MAB or by accessing your fleet on connect.altec.com/login)

 

Upper and Lower Boom Cylinder Inspection

This Mandatory Action Bulletin requires immediate action.

This Mandatory Action Bulletin requires immediate inspection of the upper boom cylinder and lower boom cylinder on units in the affected list. Altec has received a report of a cylinder failure when the lower boom was in the near vertical position. The failure of the lower boom cylinder or upper boom cylinder can cause uncontrolled boom movement. Death or serious injury can result from uncontrolled movement.

 

Investigation has determined that some upper boom cylinders and lower boom cylinders have the potential for failure. Units affected must be inspected immediately to check for the specific cylinders. The specific cylinders are identified by the design characteristic of a head gland retaining cap that is threaded to the outside of the cylinder barrel (refer to Figure 1).

 

Figure 1 — Cylinder with Externally Threaded Barrel with Retaining Cap

 

Cylinders having the specified design characteristic MUST be replaced. Until the cylinders are replaced, the booms must be operated with the following limitations (refer to Figure 2).

 

Altec Use Only
Inspection labor 0.5 hr
Repair labor 10.0 hr
Account # 010.1093.43151.000.9101.000
Travel Not included
NHTSA code 98
Prime fail P/N 035040124, 035040128
Doc ref 074900729

 

Kit Description Part Number Qty Warranty
Upper Boom Cylinder 991160224 1 Yes
Lower Boom Cylinder 991159976 1 Yes

 

  • The upper boom operation must be limited to no more than 75 degrees of unfold movement above horizontal.
  • The lower boom operation must be limited to no more than 55 degrees of raise movement above horizontal.
  • Make sure that all operators and service technicians are aware of these restricted ranges of movement.

 

If BOTH the upper boom cylinder and the lower boom cylinder DO NOT have the specified design characteristic, no cylinder replacement is needed. Return the unit to service. Complete the Inspection Sheet at the end of this MAB and return it to Altec.

 

ALL cylinders having the specified design characteristic MUST BE replaced. For each cylinder requiring replacement, locate the part number on the original cylinder, usually stamped into the barrel at the rod end of the cylinder. Compare the part number on the cylinder to the original cylinder part number listed in Figure 3. If the part numbers match, call 1-877-GO ALTEC (1-877-462-5832) to order the corresponding replacement cylinder kit shown in Figure 3. If the cylinder part number cannot be found on the cylinder barrel or the part numbers do not match, call Altec for assistance before ordering a replacement cylinder kit. Do not complete the Inspection Sheet at the end of this MAB if ordering replacement cylinder kit(s).

 

Cylinder Location Original Cylinder Part Number Replacement Kit Part Number
Upper Boom 035040124 991160224
Lower Boom 035040128 991159976

 

Figure 3 — Cylinder and Replacement Kit Part Numbers

 

The part number 991160224 replacement kit will not be in stock until mid-October 2020. Orders for both replacement kits may be delayed due to the age of the affected units and limited production availability of the replacement cylinders.

 

This repair is covered under the Altec Warranty Policy and can be performed by Altec, the customer, or the customer’s warranty provider. Altec will perform the repair for free at an Altec facility. If the customer or the customer’s warranty provider performs the repair, a warranty claim must be submitted to be reimbursed for the cost of the parts and/or labor. Altec will allow up to $45 for the labor to perform this inspection and up to $900 for the labor to replace both cylinders. Call 1-877-GO ALTEC (1-877-4625832) to schedule the work to be done by an Altec service technician. Customers are responsible for the travel costs of an Altec Mobile Service technician if the technician performs the inspection or repair at the owner’s location. If calling to schedule an Altec Mobile Service technician for this repair, confirm whether the technician will be able to perform the repair at the owner’s location. If the technician cannot do this, the repair must be performed at an Altec facility.

 


4 Affected Products

Vehicle

MAKE MODEL YEAR
ALTEC AERIAL DEVICE 1995-1998

 


8 Associated Documents

Recall Quarterly Report #3, 2021-1

RCLQRT-20V420-8911.PDF 211.304KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.35 KB]

 


Recall Quarterly Report #1, 2020-3

RCLQRT-20V420-0891.PDF 211.123KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.17 KB]

 


Defect Notice 573 Report

RCLRPT-20V420-1888.PDF 213.651KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [208.64 KB]

 


Defect Notice 573 Report

RCLRPT-20V420-5355.PDF 213.651KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [208.64 KB]

 


Recall Acknowledgement

RCAK-20V420-8141.pdf 244.584KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [238.85 KB]

 


Recall Quarterly Report #2, 2020-4

RCLQRT-20V420-8309.PDF 211.223KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.27 KB]

 


Owner Notification Letter(Part 577)

RCONL-20V420-7459.pdf 362.482KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [353.99 KB]

 


Recall Quarterly Report #4, 2021-2

RCLQRT-20V420-2479.PDF 211.409KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.45 KB]

 


Latest Recalls Documents

For the Latest and Most Recent Recalls Information Visit the link below…

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=20V420&docType=RCL

 


 

“This site contains affiliate links for which OEMDTC may be compensated”
Bestseller No. 1
TT TRSMIMA Safety Harness Fall Protection Kit: Full Body Roofing harnesses with Shock Absorbing Lanyard - Updated Comfortable Waist Pad
  • 🧰UPGRADE ACCESSORIES:Our 4 point adjustment full body harness is international version which is signed according to the highest standards in world.It adds many safe and practical accessories: this harness has as many as 4 adjustm-ent points; shoulder load-bearing loops allow you to enhance suspension protection in tight spaces; the waist of the harness has durable side D-rings can be used in work positioning to and store more spare hooks!
  • 🧰SAFETY STANDARD:This full body construction harness is the perfect roofing harness specifically designed with premier fall arrest gear.We exceeded expectations by meeting and surpassing the requirements set forth in the ANSI/ASSE Z359.11-2014 standard.This complete fall protection package includes a 2m long safety lanyard and is also compatible with other types of lanyards.We offer unmatched safety harness fall protection!Safety is our number one priority!
  • 🧰LIGHTWEIGHT & COMFORT: Ergonomic, our new patented waist padding upgrades with thick premium ventilated breathable mesh plush pads minimize muscle fatigue.Increased air flow provides faster cooling and drying,providing additional comfort for the waist.Constructed with extra-wide support belt with premium plush padding for major support, soothing comfort and lateral movements.TRSMIMA harness for construction workers will never let you "down"!
  • 🧰RELIABLY DURABLE:Our safety harness strap is made of 100% premium high strength industrial synthetic polyester fibers, which has great performance in abrasion and heat resistance.We commit that all stitching of the webbing are intact after successive tearing test in different angles at force of 25KN!.Our 4-point full body harness designed to accommodate both men and women. Waist size: 78-143cm(30.7inch-55.3inch) Leg size: 54-97cm(21.2inch-38inch), fit weigh 130-350 pounds (59 to 159 kg)
  • 🧰OSHA COMPLIANT – TRSMIMA ensures the safety and well-being of workers through setting standards and offering training, outreach, education, and assistance. Great for use in Construction, Demolition, Climbing, Hunting, Roofing, Emergency, First responder, Landscaping, Security and etc.
Bestseller No. 2
Palmer Safety Fall Protection Safety Harness w/Detachable 6' Single Leg Lanyard I EXTERNAL Shock Absorber Lanyard I OSHA/ANSI Fall Arrest Kit I Ideal for Industrial & Construction Use (Yellow - 1pk)
  • 🧰 PEACE OF MIND ON THE JOB - The Palmer Safety Harness Kit is a top-performing and heavy-duty full-body harness that exceeds industry standards set by ANSI/ASSE Z359.11-2014. This complete fall protection package includes a safety lanyard and is also compatible with other types of lanyards, such as those with shock absorbers, roof lifelines, and anchorage tethers. Feel secure while on the job knowing that the Palmer Safety fall protection harness has got you covered.
  • 🧰 EQUIPMENT CHOICE for HEIGHT - This single dorsal d-ring located on the back of the harness can be used for fall arrest, travel restraint, and even rescue operations. For more demanding work environments, additional fall prevention accessories may be required. We offer kits and combinations that include roofers anchor points and scaffold cross arm straps to ensure that all your safety needs are met.
  • 🧰 ADJUST WITH EASE - Palmer Safety full body harness is designed to accommodate both men and women, and it is essential for both safety and performance that the harness fits properly. It can be adjusted to fit users who weigh between 130 and 310 pounds (59 to 140 kg) and are between 4'10" and 6'6" tall (147 to 198 cm). To ensure a secure fit, make sure all buckles are fastened, the leg and shoulder straps are tight, and the chest strap is positioned in the center of the chest.
  • 🧰 COMPLIANT WITH SAFETY STANDARD - We exceeded expectations with our Palmer Safety Full Body Harnesses by meeting and surpassing the requirements set forth in the ANSI/ASSE Z359.11-2014 standard. This standard lays out guidelines for testing fall protection products, including the number of items to be tested, equipment used, and the roles of both the manufacturer and testing lab. You can find more information by checking the Compliance Label/Safety Label on our products.
  • 🧰 ANSI & OSHA COMPLIANCE – OSHA ensures the safety and well-being of workers through setting standards and offering training, outreach, education, and assistance. When employees are working at a height of 6 feet or more above lower levels, a personal fall arrest system is mandatory. The Palmer Safety fall protection safety harness is perfect for various job roles such as roofing, residential & commercial construction, arborist, high-rise painting, window and gutter cleaning.
Bestseller No. 3
AFP 6 FT Single Leg Internal Shock Absorbing Safety Lanyard with Dual Snap Hooks
  • ✅SAFE: The AFP 6 FT Single Leg Internal Shock Absorbing Lanyard is made with a lightweight, heavy-duty, high-strength outer polyester webbing and a polyester core specially sewn in to reduce impact forces, with two substantially secure heavy-duty double-locking gates.
  • ✅DURABLE: The tough webbing is highly resistant to abrasion, aging, and won’t soften from frequent use. This webbing has low shrink properties and a high temperature threshold.
  • ✅CONVENIENT: Our most popular 2-in-1 fall arrest single lanyard that minimizes trip hazards or fall with a shock absorber built into the lanyard, eliminating the need for an additional bulky shock pack. Elasticated leg expands from 4-1/2 to 6 feet and can resist 8,500 lbs. of tensile strength!
  • ✅COMPLIANT: Meets all applicable strict requirements of the American National Standards Institute and in compliance with the Occupational Safety and Health Administration ANZSI Z359.13-13, ANSI A10.32-12, OSHA 1926 Subpart M, OSHA 1910, including the stringent ANSI Z359.1.
Bestseller No. 4
KwikSafety - Charlotte, NC - SUPERCELL Safety Harness [2 PACK] Premium Shoulder Padding ANSI OSHA Full Body Fall Protection Work Equipment Construction Tower Climbing Roofing Forklift Aerial Boom Lift
  • 3 HEAVY DUTY D-RINGS | SHOULDER PAD SUPPORT - The KwikSafety SUPERCELL is a premium, durable, high performance full body harness that meets & exceeds ANSI/ASSE Z359.11-2014 standards. Our safety harness fall protection features: (2) hip d-rings & (1) dorsal d-ring for fall arrest attachment, travel restraint & rescue, (2) cushioned shoulder pads, (1) pass-through buckles & (2) tongue buckles to ensure proper fit, & premium stitched load bearing straps made from a non-recycled synthetic material.
  • FREE TOOL LANYARD & BAG - Fall arrest harness d ring harness made of 100% polyester quality stitched yellow & black aerial lift harness straps. Correct fitting construction harness is essential for proper performance for men & women. Supports users within the capacity range of 130-310Ibs (59-140kg), 4'10"-6'6" (147-198cm). To ensure your fall arrest safety harnesses fit properly, see that all buckles are connected, leg & shoulder straps are snug & chest straps are in the center of the chest.
  • OSHA APPROVED SAFETY HARNESS - The best construction body harness for those who need safety first but want premium product & style. Fall protection body harness men ideal use: construction harnesses, climbing harness, ironworkers harness, roofing harness, construction harness women, rescue chest harness, security harness, forklift harness, safety harness lineman & harness tower climbing. Mens harness also for high-rise window cleaning, gutter cleaning, painting harness & search/rescue.
  • FALL PROTECTION HARNESS - Safety harnesses are crucial PPE used in various industries to prevent falls & injuries. They consist of adjustable straps, buckles, & attachment points designed to secure a worker to an anchor point. When properly worn & connected, safety harnesses distribute the force of a fall across the body, reducing the risk of serious injury. Safety harnesses are necessary for workers in construction, roofing & other high-risk occupations.
  • THE SAFETY YOU NEED, THE STYLE YOU WANT - Safety harnesses offer a secure fit for users of all shapes & sizes, ensuring both safety & peace of mind. Harnesses play a vital role in mitigating the risks associated w/ working or engaging in activities at elevated heights. The proper use of safety harnesses significantly reduces the risk of accidents or injuries, and regular inspections ensure harnesses remain in optimal condition, providing reliable protection for workers operating at heights.
SaleBestseller No. 6
Palmer Safety Fall Protection Full Body 5 point Harness, Padded Back Support, Quick-Connect Buckle, Grommet Legs, Back&Side D-Rings, OSHA ANSI Industrial Roofing Tool Personal Equipment (Blue - LG)
  • 🧰 RELIABLE PROTECTION AND SUPPORT: The Palmer Safety 5 point adjustment harness offers superior protection and support for workers in a range of industries, with a customized fit for maximum comfort and safety, and sturdy buckles and straps that can be easily adjusted to fit a range of users.
  • 🧰 HIGH-STRENGTH STEEL D-RINGS: The dorsal D-ring and hip D-rings are made of high-strength steel, and support users within the capacity range of 130 to 420 pounds, making the Palmer Safety harness a reliable choice for fall protection and arrest in industries such as construction, roofing, oil and gas, and utilities.
  • 🧰 COMFORT AND CONVENIENCE: The heavy duty back support/positioning pad with removable tool belt provides added comfort and convenience on the job, with a thick, padded construction that helps distribute weight evenly and a removable belt that allows the user to carry tools and equipment easily.
  • 🧰 EASY TO USE: The tongue and buckle leg straps and quick connect chest make the Palmer Safety harness quick and easy to put on and take off, with simple, intuitive buckles and straps that can be quickly adjusted to fit the user's body, even while wearing gloves or other protective gear.
  • 🧰 ADDED PROTECTION AND PEACE OF MIND: The sewn in back pad and fall indicators offer added protection and peace of mind for workers in high-risk environments, with a padded construction that helps protect the user's back and shoulders, and built-in indicators that make it easy to tell if the harness has been involved in a fall. Meets or exceeds ANSI Z359.11-2014 and A10.32-2012 standards, and is available in multiple sizes & colors to fit a range of workers and work environments.
Bestseller No. 7
KwikSafety - Charlotte, NC - SCORPION Safety Harness [w/attached 6ft. Tubular Lanyard on back] OSHA ANSI Fall Protection INTERNAL Shock Absorbing Lanyard/Construction Carpenter Scaffolding
  • FALL PROTECTION GEAR - The KwikSafety SCORPION is a durable, heavy duty, high performance Full Body Harness that meets and exceeds ANSI/ASSE Z359.11-2014 standards. Our harness fall protection is the complete support package because the SCORPION includes a fall protection safety lanyard! The harness is also compatible with other lanyards with shock absorbers, roof lifelines, and anchorage tether lanyards. Safely perform the job knowing the SCORPION fall protection harness has your back!
  • HEAVY DUTY D-RING - One back dorsal ring is all it takes to provide functionality on the construction job. The dorsal ring is used for fall arrest & can be used for travel restraint or rescue. The pass-through buckles on our universal harness are made out of synthetic material that is superior to polyester. For some jobs, more fall prevention accessories may be necessary. If an anchor point is needed, like a roofers anchor point or scaffold cross arm strap, we have kits and combos available!
  • OSHA COMPLIANT - This construction harness is an essential part to any workers positioning system & is ideal for any job where OSHA compliance is required. This full body harness supports users within the capacity range of 130 - 310LBS (59 to 140 kg), 4’10” to 6’6” (147 to 198 centimeters) due to the adjustment points. To ensure your harnesses properly fit, see that all buckles are connected, leg & shoulder straps are snug, & chest straps are in the center of the chest area.
  • FALL PROTECTION HARNESS - Safety harnesses are crucial PPE used in various industries to prevent falls & injuries. They consist of adjustable straps, buckles, & attachment points designed to secure a worker to an anchor point. When properly worn & connected, safety harnesses distribute the force of a fall across the body, reducing the risk of serious injury. Safety harnesses are necessary for workers in construction, roofing & other high-risk occupations.
  • THE SAFETY YOU NEED, THE STYLE YOU WANT - Safety harnesses offer a secure fit for users of all shapes & sizes, ensuring both safety & peace of mind. Harnesses play a vital role in mitigating the risks associated w/ working or engaging in activities at elevated heights. The proper use of safety harnesses significantly reduces the risk of accidents or injuries, and regular inspections ensure harnesses remain in optimal condition, providing reliable protection for workers operating at heights.
Bestseller No. 8
TT TRSMIMA Safety Harness Fall Protection Upgrade 4 Quick Buckles Construction Full Body Harness with 6 Adjustment D-ring
  • ✅UPGRADE ACCESSORIES:Our full body harness is international version which is designed according to the highest standards in world.It adds many safe and practical accessories: this harness has as many as 4 quick release buckles; shoulder load-bearing loops allow you to enhance suspension protection in tight spaces; chest attachment points improve safety when you climb high (such as poles); the chest of the harness has extra hanging loops to help you store more spare hooks!
  • ✅CERTIFIED with Both OSHA and ANSI:This full body construction harness is the perfect roofing harness specifically designed with premier fall arrest gear.The compliancy guidelines met include: ANSI Z359.11-2014, ANSI A10.32-12, OSHA 1926 Subpart M, OSHA 1910. We offer unmatched safety harness fall protection!Safety is our number one priority !The Trsmima System exceeds the already-rigorous ANSI testing standards and is heavy-duty, high-performance fall protection you can trust to have your back.
  • ✅LIGHTWEIGHT & COMFORT: Ergonomic, our new patented shoulder, leg, and back padding upgrades with thick premium ventilated breathable mesh plush pads minimize overhead muscle fatigue.Increased air flow provides faster cooling and drying,providing additional comfort for the shoulders, legs and back.Constructed with extra-wide 8''back support belt with premium plush padding for major support, soothing comfort and lateral movements.TRSMIMA harness for construction workers will never let you "down"!
  • ✅RELIABLY DURABLE:Our safety harness strap is made out of 100% premium high strength industrial synthetic polyester fibers, which has great performance in abrasion and heat resistance.We commit that all stitching of the webbing are intact after successive tearing test in different angles at force of 25KN!Proper fit is essential for convenience in work at height, our harness safety offers 6 adjustm-ent points for users to ensure proper fit within the weight capacity range of 130 to 350 pounds !
  • ✅SAFE:TRSMIMA cannot tolerate any defective product outgoing factory.We focus on servicing the industrial and residential contractors to the weekend DIY warrior with our brand TRSMIMA in rope, personal protective equipment and fall protection.Customer service and satisfaction is the key to our success by delivering great products quickly and at reasonable prices!
Bestseller No. 9
AFP Universal Full-Body Fall Protection Safety Harness w/Dorsal D-Ring Tongue Buckle Legs Hi-Viz Green, Shock Absorbing Lanyard (OSHA/ANSI Rated) (1 Pack, Harness + Single Leg Lanyard w/Snap Hooks)
  • ✅COMFORT – Designed with reinforced edges for added comfort and relief. Water-wicking material averts the harness from sweat and water deterioration. Harness is designed to allow for better lateral movements.
  • ✅RELIABLE – Standout and be easily spotted with our high-visibility green harness. Alloy steel D-ring ensures all weather performance preventing corrosion against all weather conditions. Rugged construction endures rough use, standing up to long periods of outdoor elements including sun exposure without tearing or fraying for added longevity.
  • ✅SAFE – The AFP 6 FT Internal Shock Absorbing Lanyards are made with lightweight, heavy-duty, high-strength outer polyester webbing and a polyester core specially sewn in to reduce impact forces, with two substantially secure heavy-duty double-locking gates.
  • ✅DURABLE – The tough webbing is highly resistant to abrasion, aging, and won’t soften from frequent use. This webbing has low shrink properties and a high temperature threshold.
  • ✅CONVENIENT – Our most popular 2-in-1 fall arrest lanyards that minimizes trip hazards or fall with a shock absorber built into the lanyard, eliminating the need for an additional bulky shock pack. Elasticated leg expands from 4-1/2 to 6 feet and can resist 8,500 lbs. of tensile strength!
Bestseller No. 10
Ymachray Fall Protection Safety Harness OSHA/ANSI Compliant,internal Shock Absorbing landyard&Hook
  • ANSI/ASSE Z359.11-2014 COMPLIANT: Ymachray Full Body Harnesses have the fully passed test report performed at authoritative laboratory in accordance with ANSI/ ASSE Z359.11-2014 and in compliance with the requirements of ANSI Z359.13-2013. Or the user must read and fully understand the limitations and proper use of the Fall protection equipment, and be properly trained by the Competent Person prior to use.
  • SAFETY DESIGN PERFORMANCE: Ymachray Full Body Harnesses are used for fall arrest, positioning, travel restraint, suspension and rescue applications. When supported by the dorsal attachment during a fall, the design of our Full Body Harness directs load through the shoulder straps supporting the user, and around the thighs. After a fall, our Full Body Harness will support users and post fall at an angle within 30° to vertical.
  • HEAVY DUTY D-RING: One back dorsal ring is all it takes to provide functionality on the construction job. The dorsal ring is used for fall arrest & can be used for travel restraint or rescue. The pass-through buckles on our universal harness are made out of synthetic material that is superior to polyester. Tensile strength (max load) for the snap hook is rated at 5,000 pounds with a gate strength of 3,600 pounds. Meets American National Standards Institute ASTM F1774 standards.
  • WARRANTY: All the Ymachray Full Body Harness Kit have the fully passed test report in accordance with ANSI/ASSE Z359.11-2014 & ANSI Z359.13-2013. ASTM F1774 Certified ,SAFE and GUARANTEED. 45 Days Money-Back & 2 Years Warranty, When You Are Not Satisfied with Our Product, Please Don't Hesitate to Contact Us. BUY WITH CONFIDENCE.
  • Double Leg Internal Shock Absorbing Safety Fall Protection Lanyard ASTM F1774 Certified: The Shock Absorbers are designed for up to 6-foot free fall applications with a maximum capacity up to 310 lb. (141 kg) including clothing, tools, etc. with a maximum deployment distance of 48 inch/1.2m & average arresting force 900lbs. Statically tested with a minimum breaking strength more than 5,000 pounds (22.2 kN).

Last update on 2024-03-13 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...