2017-2020 Altec Aerial Devices CSN767 Exhaust System Heat Shield

“This site contains affiliate links for which OEMDTC may be compensated”

July 10, 2020 NHTSA CAMPAIGN NUMBER: 20V401000

Oil Leak from PTO May Cause Fire

Oil absorbed by the exhaust heat shield thermal blanket has an increased risk of a fire from being exposed to hot engine components.

 

NHTSA Campaign Number: 20V401

Manufacturer Altec Industries Inc.

Components EQUIPMENT, ENGINE AND ENGINE COOLING

Potential Number of Units Affected 2,550

 

Summary

Altec Industries, Inc. (Altec) is recalling certain 2017-2020 AT200A, AT235, AT37-G, AT40-G, AT41/48M Aerial Devices mounted on a Ford F-350, F-450 or F-550 chassis equipped with a gas engine and Chelsea 249 Power Take-Off (PTO). The PTO may leak oil onto the exhaust heat shield thermal blanket.

 

Remedy

Altec will notify owners, and dealers will inspect and replace the heat shield with a redesigned version, as well as install plumbing to relocate a pressure switch and install hoses with improved routing to increase their distance from heat sources, free of charge. The recall began September 8, 2020. Owners may contact Altec customer service at 1-877-462-5832. Altec’s number for this recall is CSN 767.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 


IMPORTANT SAFETY RECALL

This notice applies to your vehicle. See attached serial number list

NHTSA Safety Recall
No. 20V-401

September 1, 2020

 

Dear Altec Owner,

This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act, and Canada Motor Vehicle Safety Act.

 

Altec Industries, Inc. has decided that a defect which relates to motor vehicle safety exists in certain units which are installed on model year 2017-2020 Ford F350 and F550 gas chassis. Over time, low volume fluid leakage can be absorbed in the exhaust heat shield thermal blanket. This can lead to a fire. Death or serious injury can result from a fire.

 

Refer to CSN 767 for the items covered under the warranty policy. Altec will supply, free of charge, a heat shield kit and other parts as required to correct this condition.

 

In order to determine if your unit is affected by CSN 767, compare the serial number of your unit with the list of affected units attached to the CSN. The repair can be performed by the customer or you may contact Altec at 1-877-GO-ALTEC (1-877-462-5832) for further assistance. The repair is expected to take up to 9 hours to complete.

 

At any time, you may contact Altec at 1-877 GO ALTEC (1-877-462-5832) with your unit’s serial number to determine if there are any other outstanding notices.

 

For US owners: after contacting Altec, if you are still not able to have the safety condition remedied without charge and within a reasonable time, you may submit a complaint to: Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue SE, Washington, DC 20590 or call toll-free 1-888-327-4236 (TTY: 1-800-424-9153) or  go to https://www.safercar.gov.

 

For Canadian Owners: if you are still not able to have the safety condition remedied by your dealer within a reasonable time, please contact Altec Customer Service at 1-877-GO-ALTEC (1-877-462-5832).

 

If you had this repair performed before you received this letter, you may be eligible to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this recall. If you have sold or retired the unit please call Altec at 1-877-GO-ALTEC (1-877-462-5832) so the records may be changed.

 

If you have leased this equipment to another person or company, you are required by Federal Law to forward a copy of this notice to the lessee by first class mail within ten (10) days of the receipt of this notice.

 

We are sorry to cause this inconvenience; however we are taking this action in the interest of your safety and continued satisfaction with Altec products.

 

Thank you for your immediate attention on this important matter.


CSN 767

Customer Service Notice

September 1, 2020

Units Affected: Units installed on model year 2017-2020 Ford F350 and F550 gas chassis (please verify that your unit serial number is affected by reviewing the attached list in this CSN or by accessing your fleet on connect.altec.com/login)

 

Exhaust System Heat Shield Inspection

Altec is committed to providing our customers with safe and reliable products from initial delivery throughout the useful life of the unit.

 

On the affected units, Altec has received reports of low volume hydraulic oil or transmission fluid leakage saturating the thermal blanket within the exhaust system heat shield. In addition, certain components under the cab may have insufficient protection from the heat of the exhaust system and from adjacent moving parts. One or more of these issues has caused a thermal event under the cab on some affected units, resulting in property damage. Death or serious injury can result from a thermal event.

 

Altec requires an inspection of the exhaust thermal blanket and associated components to be performed within 30 days of the receipt of this CSN. The Inspection Procedure begins on page 3. If the inspection indicates that components in addition to the heat shield must be replaced, call 1-877-GO ALTEC (1-877-462-5832) to order the required additional part(s) from the list in Figure 1.

 

Altec requires a Heat Shield Kit to be ordered for each affected unit within 60 days of the receipt of this CSN. This kit will be used to replace the exhaust system heat shielding. During the installation of this kit, additional protection will be added to wiring and hoses as needed, and components will be replaced or separated from adjacent moving parts as needed. Call 1-877-GO ALTEC (1-877-462-5832) to order the appropriate Heat Shield Kit from the list in Figure 2.

 

Altec Use Only
 Inspection labor 0.5 hr
 Repair labor 3.0 hr
 Account # 010.0777.43151.758.0000.000
 Travel Not included
 NHTSA code 23
 Prime fail P/N None
 Doc Ref 074900730, 074900731

 

Altec Use Only
 Parts Description Part Number Qty  Warranty
 Heat shield kit, model years 2017-2019 991177956 1 Yes
 Heat shield kit, model year 2020 991178154 1 Yes
 PTO pressure switch, Chelsea 970034398 1 Yes
 PTO solenoid, Chelsea 970166447 1 Yes
 PTO pressure switch, Muncie, model year 2020 970306613 1 Yes
 PTO solenoid, Muncie, model year 2020 970774244 1 Yes
 Suction hose None 1 Yes
 Pressure hose None 1 Yes
 -12 SAE to -12 JIC 45 degree elbow 027410057 1 Yes
 -10 SAE to -8 JIC 45 degree elbow 027410055 1 Yes
 Heat shield wrap 970184662 1’ Yes
 Stainless steel cable tie 970282369 6 Yes
 Hose sleeve 990290555 2’ Yes

 

Chassis Model Year Description Part Number Quantity
All PTO pressure switch, Chelsea 970034398 1
All PTO solenoid, Chelsea 970166447 1
2020 PTO pressure switch, Muncie 970306613 1
2020 PTO solenoid, Muncie 970774244 1
All Suction hose, -16, 62-300 psi, Parker #811-16 or equivalent, with length and end fittings matching original hose Obtain locally 1
All Pressure hose, -8, 3,000 psi, Parker GlobalCore #387TC-8 or equivalent, with length and end fittings matching original hose Obtain locally 1
2020 -12 SAE to -12 JIC 45 degree elbow 027410057 1
2020 -10 SAE to -8 JIC 45 degree elbow 027410055 1
2020 Heat shield wrap 970184662 1’
2020 Metal cable tie 970282369 6
2020 Fabric hose sleeve 990290555 2’

 

Figure 1 — Replacement Parts, Order as Required Based on

Inspection Procedure or as Determined During Installation of Heat Shield Kit

 

Chassis Model Year Description Part Number
2017-2019 Heat Shield Kit 991177956*
2020 Heat Shield Kit 991178154*

 

*Availability is limited until mid to late September 2020

Figure 2 — Heat Shield Kits, Order Within 60 Days of Receipt of this CSN

 

If the unit fails the inspection, it must be taken out of service until the Heat Shield Kit and other required replacement components are installed.

 

If the unit passes the inspection, the Heat Shield Kit must be installed within 120 days of the receipt of this CSN, with the Inspection Procedure repeated weekly until the kit is installed.

 

This inspection and repair are covered under the Altec Warranty Policy and can be performed by Altec, the customer, or the customer’s warranty provider. Altec will perform the inspection and repair for free at an Altec facility. If the customer or the customer’s warranty provider performs the inspection and/or repair, a warranty claim must be submitted to be reimbursed for the cost of the parts and/or labor. Altec will allow up to $45 for the labor to perform this inspection and up to $270 for the labor to perform this repair. Call 1-877-GO ALTEC (1-877-462-5832) to schedule the work to be done by an Altec service technician. Customers are responsible for the travel costs of an Altec Mobile Service technician if the technician performs the inspection and/or repair at the owner’s location.

 

Inspection Procedure

A mechanic’s creeper and a flashlight are required for the inspection procedure. Use the Decision Chart on page 6 to assist in determining the required actions. Read and understand the entire procedure before beginning.

  1. Position the unit on a level surface, apply the parking brake, and chock the wheels. Turn off the engine and remove the key. Allow the exhaust system to cool to the touch.

 

  1. Using a mechanic’s creeper, get under the chassis near the power take-off (PTO) on the driver’s side of the transmission.

 

  1. Find the heat shield that is attached with band clamps around the exhaust pipe near the PTO (refer to Figure 2). The thermal blanket inside the metallic covering of the heat shield is exposed at the seam on the bottom and at the front. Touch the thermal blanket by hand every few inches along the seam to determine if it is wet with fluid.

 

Figure 2 — Exhaust Heat Shield

 

  1. Inspect the following parts for damage from heat and/or abrasion.
    • PTO pressure switch housing (refer to Figure 3)
    • PTO pressure switch wiring if it is not covered with heat shield tubing (refer to Figure 3)
    • PTO solenoid housing (refer to Figure 4)
    • PTO solenoid wiring if it is not covered with heat shield tubing
    • Suction and pressure hoses connected to the pump (refer to Figure 5)

 

  1. If the thermal blanket is wet, inspect the following parts for oil leakage.
    • PTO pressure switch housing
    • PTO solenoid housing
    • PTO to transmission mating surface
    • Hydraulic pump to PTO mating surface
    • All hydraulic fittings on PTO and pump

 

Figure 3 — PTO Pressure Switch

 

Figure 4 — PTO Solenoid

 

  1. If the thermal blanket is dry, inspect for evidence of low volume hydraulic or transmission oil leakage onto the metal covering of the heat shield, such as dark spots from burnt fluid. If such evidence is seen, inspect the following parts for oil leakage.
    • PTO pressure switch housing
    • PTO solenoid housing
    • PTO to transmission mating surface
    • Hydraulic pump to PTO to mating surface
    • All hydraulic fittings on PTO and pump

 

  1. Review the inspection results from steps 3 through 6.
    • If the thermal blanket is wet with fluid, take the unit out of service until the Heat Shield Kit is installed and any damaged or leaking component(s) are repaired or replaced. Order the Heat Shield Kit and replacement(s) for damaged or leaking component(s) as described on page 1 of the CSN.
    • If the PTO pressure switch or wiring, PTO solenoid or wiring, suction hose, or pressure hose are damaged from heat and/or abrasion, take the unit out of service until the Heat Shield Kit is installed and the damaged component(s) are replaced. Order the Heat Shield Kit and replacement(s) for damaged component(s) as described on page 1 of the CSN.
    • If the PTO pressure switch and wiring, PTO solenoid and wiring, suction hose, and pressure hose are not damaged from heat and/or abrasion, and the thermal blanket is dry but there is evidence of fluid leakage onto the metal heat shield covering, the unit can remain in service. Make repairs immediately to any leaking component(s) that can be fixed without replacement.
    • If the replacement of any leaking component(s) is required, order the Heat Shield Kit and the replacement component(s), as described on page 1 of the CSN. INSPECT THE THERMAL BLANKET DAILY as described in steps 1 through 3 until the Heat Shield Kit is installed and any leaking components(s) are replaced. If the daily inspection finds that the thermal blanket has become wet, take the unit out of service.
    • If no components require replacement due to leaking, order the Heat Shield kit as described on page 1 of the CSN. REPEAT THE INSPECTION PROCEDURE WEEKLY until the Heat Shield Kit is installed.
    • If the thermal blanket is dry, there is no evidence of fluid leakage, and the PTO pressure switch and wiring, PTO solenoid and wiring, suction hose, and pressure hose are not damaged from heat and/or abrasion, the unit can remain in service. Order the Heat Shield Kit as described on page 1 of the CSN. REPEAT THE INSPECTION PROCEDURE WEEKLY until the Heat Shield Kit is installed.

 


4 Affected Products

Vehicle

MAKE MODEL YEAR
ALTEC AERIAL DEVICE 2017-2020

 


9 Associated Documents

Recall Acknowledgement

RCAK-20V401-8803.pdf 245.219KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [239.47 KB]

 


Defect Notice 573 Report

RCLRPT-20V401-5930.PDF 213.405KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [208.40 KB]

 


Recall 573 Report- Amendment 1

RCLRPT-20V401-5763.PDF 213.823KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [208.81 KB]

 


Recall Quarterly Report #3, 2021-1

RCLQRT-20V401-5251.PDF 211.328KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.38 KB]

 


Recall Quarterly Report #1, 2020-3

RCLQRT-20V401-1845.PDF 211.136KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.19 KB]

 


ISSUED Owner Notification Letter(Part 577)

RCONL-20V401-4241.pdf 886.516KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [865.74 KB]

 


Recall Quarterly Report #2, 2020-4

RCLQRT-20V401-3186.PDF 211.245KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.29 KB]

 


Recall 573 Report- Amendment 2

RCLRPT-20V401-8283.PDF 214.316KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [209.29 KB]

 


Recall Quarterly Report #4, 2021-2

RCLQRT-20V401-7828.PDF 211.439KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.48 KB]

 


Latest Recalls Documents

For the Latest and Most Recent Recalls Information Visit the link below…

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=20V401&docType=RCL

 


 

SaleBestseller No. 2
Starfire Premium Lubricants AW 32 Hydraulic Oil, 5 Gallon, Pail
  • Formulated with premium base stocks for added resistance to thermal breakdown
  • Outstanding wear protection
  • Excellent resistance to system rust and oil oxidation
  • Maintains excellent water separating properties
  • Excellent foam control and air release deliver consistent system operation
Bestseller No. 3
Star Fire Premium Lubricants AW 46 Hydraulic Oil, 5 Gallon, Pail
  • Formulated with premium base stocks for added resistance to thermal breakdown
  • Outstanding wear protection
  • Excellent resistance to system rust and oil oxidation
  • Maintains excellent water separating properties
  • Excellent foam control and air release deliver consistent system operation
Bestseller No. 4
Johnsen's 5594 Hydraulic Jack Oil - 32 oz.
  • Hydraulic Jack Oil
  • Formulated to perform at a wide range of temperatures
  • Contains anti-foam additives and rust inhibitors
  • Reduces friction
  • It is mixable with other standard hydraulic jack oils
Bestseller No. 6
MAG 1 AW32 10-Weight Hydraulic Fluid - 1 Gallon
  • MAG 1 AW32 (ISO32) 10-Weight Hydraulic Fluid is a high quality oil that is ideal for use in most 2-stage log splitter pumps. Benefits include exceptional protection against wear from contaminants and higher operating temperatures and pressures ensures longer equipment life.
Bestseller No. 7
Lucas Oil 10019 Hydraulic Oil Booster and Stop Leak - 1 Quart
  • Reduces the operating temperature of hydraulic systems
  • Conditions old seals and O-rings to stop and prevent future leaks
  • Well suited for use in equipment with wet brakes
  • Removes varnish and restores pressure for more efficient operation
  • Compatible with both synthetic and conventional hydraulic fluids
Bestseller No. 8
Starfire Premium Lubricants Aw 68 Hydraulic Oil, 5 Gallon, Pail
  • Formulated with premium base stocks for added resistance to thermal breakdown
  • Outstanding wear protection
  • Excellent resistance to system rust and oil oxidation
  • Maintains excellent water separating properties
  • Excellent foam control and air release deliver consistent system operation
Bestseller No. 9
Ultra1Plus U1P-Duty ISO 68 AW Hydraulic Fluid
  • Extended Equipment Life: U1P-Duty ISO 68 AW Hydraulic Oil ensures 7,000 hours of reliable operation with top-tier additives, protecting against oxidation, corrosion, and wear for prolonged machinery life.
  • Complete Protection: Its comprehensive additives resist rust, foam, and varnish formation, maintaining smooth operation, preventing filter blockage, and ensuring consistent viscosity over time.
  • Versatile Performance: Suitable for high-pressure industrial applications, this fluid remains stable across wide temperature ranges, safeguarding critical components and seals.
  • Premium Lubrication: Formulated with quality base stocks and anti-wear additives, it creates a robust film, guarding pumps, pistons, and cylinders from wear, promoting equipment longevity.
  • Efficiency and Cleanliness: Its exceptional detergency, water separation, and anti-oxidation properties ensure equipment cleanliness, reducing sludge buildup and optimizing performance.
Bestseller No. 10
Starfire Premium Tractor Hydraulic & Transmission Fluid (J20C Equivalent)
  • Formulated with highly refined group ii base stocks for added resistance to thermal breakdown
  • Superior wear protection to protect critical components
  • Excellent frictional properties for smooth-shifting, excellent anti-shudder performance
  • J20c equivalent, protection against varnish and sludge formation
  • Superior thermal stability and oxidation resistance, good seal compatibility

Last update on 2024-03-12 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...