“This site contains affiliate links for which OEMDTC may be compensated” |
January 30, 2018
A brake fluid leak or air ingestion can lengthen the distance needed to stop the vehicle, increasing the risk of a crash.
NHTSA Campaign Number: 18V078
Manufacturer Jayco, Inc.
Components SERVICE BRAKES, HYDRAULIC
Potential Number of Units Affected 17
Summary
Jayco, Inc. (Jayco) is recalling certain 2017 Precept motorhomes. The brake Hydraulic Electronic Control Units (HECU) on these vehicles may be missing valve block ball plugs, potentially causing a brake fluid leak or air ingestion during electronic brake distribution and/or ABS activation.
Remedy
Jayco will notify owners, and Ford dealers will inspect the hydraulic block and replace the HECU if the ball plugs are present, free of charge. The recall began on February 16, 2018. Owners may contact Jayco customer service at 1-800-517-9137.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
February 2018
IMPORTANT SAFETY RECALL
This Notice Applies To Your Recreational Vehicle VIN #
NHTSA Recall Campaign # 18V-078
Name
Address
City, State, Zip
Dear Valued Customer:
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.
Jayco has decided that a defect which relates to motor vehicle safety exists in certain Model Year 2017 Precept Class A motorhomes built on a chassis supplied by Ford.
According to Ford Motor Company, the Hydraulic Electronic Control unit (HECU) in the braking system may have been built without ball plugs in the hydraulic block. This could result in air ingestion or brake fluid leaking during an Electronic Brake Distribution (EBD) or Anti-lock Brake System (ABS) activation. This may cause the following conditions increasing the risk of a crash:
- Air ingestion may result in unexpected, increased brake pedal travel.
- The amount of brake fluid that leaks is dependent on the number and duration of EBD and ABS events that occur. Sufficient loss of brake fluid may result in increased pedal travel and/or increased stopping distance. The brake warning light may illuminate as a result.
Ford will inspect the hydraulic block and replace the HECU if the ball plugs are not present, free of charge (parts and labor). The time needed for this repair is approximately 4 hours.
Please contact the Ford Motorhome Customer Assistance Center toll free at 1-866-906-9811 to obtain the Recall Remedy. Please reference FORD RECALL 17S41 when speaking to a Ford representative.
If you take your recreational vehicle to the Ford on the agreed service date and the dealer does not remedy this condition on that date or within three (3) days, please contact Jayco Customer Service Department at 800-517-9137. If after contacting Ford and Jayco Customer Service, you are not able to have the safety defect remedied without charge and/or within a reasonable time, you may wish to submit a written complaint to the Administrator, national Highway Traffic Safety Administration, 1200 New Jersey Avenue, SE., Washington, DC 20590; or call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153): or go to https://www.safercar.gov.
We certainly regret this inconvenience; however your safety is our most important priority.
Sincerely,
Jayco Motorized Division
1 Affected Product
Vehicle
MAKE | MODEL | YEAR |
JAYCO | PRECEPT | 2017 |
5 Associated Documents
Defect Notice 573 Report
RCLRPT-18V078-2491.PDF 214.526KB
ISSUED Owner Notification Letter(Part 577)
RCONL-18V078-2877.pdf 84.148KB
Manufacturer Notices(to Dealers,etc)
RCMN-18V078-1698.pdf 152.312KB
Defect Notice 573 Report
RCLRPT-18V078-2491.pdf 214.526KB
Recall Acknowledgement
RCAK-18V078-7263.pdf 246.036KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=18V078&docType=RCL
- Provides an extra margin of safety in extreme braking conditions
- Mix of polyglycol ethers ensures hot brake-system operation will not create dangerous vapor
- Excellent for ABS, disc and drum brake systems
- Delivers braking power when needed by avoiding a spongy pedal
- Both wet and dry boiling points exceed the minimum government standards
- High quality blend of polyethylene glycol ethers and additives
- Compatible with all brake system rubber components and other brake fluids
- Prevents seal hardening or softening
- Protects against rust and corrosion
- Provides excellent lubricity
- High compatibility. Use with or direct replacement for DOT 3, DOT 4, and DOT 5. 1
- Extended Service Interval (ESI): Lasts 100% longer than DOT 3, 50% longer than DOT 4, and 10% longer than DOT 5. 1
- Exceeds all DOT 3, DOT 4, and DOT 5. 1 standards
- Wet boiling point ~ 365 DegreeF/Viscosity at -40 DegreeC ~ 685mm2/s
- Standard brake fluid has a recommended change interval of 2 years. The recommended change interval for Bosch ESI6 is 3 years.
- Premium DOT 3 Brake Fluid has a minimum boiling point of 450°F
- Meets and exceeds DOT 3 and all other Federal and SAE specifications and standards for motor vehicle brake fluids
- Mixes with all DOT 3 approved brake fluids
- Designed for use in disc, drum and ABS brake systems
- Synthetic quality brake fluid
- Contains special ingredients to guard against vapor lock and moisture absorption
- Exceeds requirements for both DOT 3 and DOT 4 brake fluids
- Specially formulated for DOT 4 brake fluid applications
- Designed for use in disc, drum and ABS brake systems
- Premium brake and hydraulic clutch fluid that protects internal components from corrosion under normal use
- High boiling point to minimize brake fluid boiling and vapor lock
- Excellent low temperature capability and stability when used where lower cold viscosities are required
- Excellent low temperature capability and stability when used where lower cold viscosities are required
- The 336⁰F wet boil point and 521⁰F dry boil point exceeds common characteristics for DOT 4 brake fluids
- Provides corrosion protection in brake components
- Matches needs of all DOT 4 manufacturer recommendations
- Compatible with all DOT 3 and DOT 4 applications
- Minimal decrease of boiling point due to excellent water locking properties
- Non-foaming when filling and bleeding the brake system
- Excellent corrosion protection due to selected additives
- High safety tolerance against steam bubbles
- Makes brake fluid changing intervals of up to 3 years possible
- 2 Pack
- Dry boiling point 594 degrees F
- Motul 600 brake fluid is 100 percent synthetic and has an extremely high boiling poin
- Helping to prevent vapor lock and brake fade during hard use
- This brake fluid exceeds both DOT 3 and DOT 4 specifications
Last update on 2024-04-12 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.