“This site contains affiliate links for which OEMDTC may be compensated” |
August 28, 2019 NHTSA CAMPAIGN NUMBER: 19V626000
Loose Power Steering Mounting Bolts
A loose steering column shaft may cause a loss of steering control, increasing the risk of a crash.
NHTSA Campaign Number: 19V626
Manufacturer Entegra Coach
Components STEERING
Potential Number of Units Affected 101
Summary
Entegra Coach (Entegra) is recalling certain 2019-2020 Insignia, Anthem, Aspire, Cornerstone, Reatta, and Reatta XL motorhomes. The upper and lower steering shaft bolts may have been insufficiently tightened, allowing the steering column shaft to come loose.
Remedy
Entegra will notify owners, and dealers will inspect and tighten the upper and lower steering shaft bolts, as necessary, free of charge. The recall began September 23, 2019. Owners may contact Entegra customer service at 1-800-517-9137. Entegra’s number for this recall is 9901434.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Bulletin Type: | RECALL | Publication Date: | September 23,2019 |
Bulletin #: | 19V-625 Jayco
19V-626 2019-447 Entegra |
Make: | Jayco Motorized Entegra |
Job Code: | 9903434 | Models: | Embark Insignia, Aspire, Anthem, Cornerstone, Reatta |
Flat Rate: | RC024 Inspection of two bolts NO repair required .25 Hour
RC025 Inspect and repair .5 Hour |
Model Year: | 2019 & 2020 |
Incident: | Upper and lower steering shaft bolts on steering column may not be torqued correctly at 45ft lbs. |
Affected Units: | Serial Number listing of affected units is on last page of Instructions |
Misc. Tools & Supplies: | Torque wrench (Ft/Lbs
11/16 socket |
INSTRUCTIONS – Anthem, Cornerstone & Aspire(LOWER steering shaft bolt)
FIG 1: Open the generator compartment using the switch (arrow) inside the driver side front electrical compartment.
FIG 2: Bolt is located on the right side of the generator behind the washer fluid bottle (arrow).
FIG 3: Bolt location is circled in this photo.
FIG 4: Arrow is pointing to the Steering Slip Shaft bolt.
- Move wiring out of the way to see it.
- IF WHITE LINE RUNNING FROM BOLT HEAD TO THE NUT – NO REPAIR IS REQUIRED – BOLT WAS TORQUED TO 45FT LBS PRIOR TO SHIPPING.
FIG 5: IF WHITE LINE IS NOT VISIBLE – TORQUE PER
SPECIFICATIONS
- Bolt head size takes a 5/8” socket or wrench.
- Nut size takes an 11/16” socket
- Use a torque wrench and torque the nut to 45 ft./lbs.
- Mark the bolt with a white line as shown in photo to indicate the bolt has been torqued properly.
INSTRUCTIONS – Anthem, Cornerstone & Aspire (UPPER steering shaft bolt)
FIG 6:
- Upper steering shaft bolt is located on the steering column, beneath the steering wheel and under the large rubber boot.
- Lower the rubber boot on the steering column to see the bolt.
FIG 7:
- Examine the upper steering shaft bolt ( front and back side of the steering column).
- If the bolt has been properly torqued at the factory there will be a white line running from the head of the bolt to the nut end of the bolt on the dash side of the steering column as shown in this photo (arrow).
IF THE WHITE LINE IS NOT VISIBLE PROCEED TO NEXT STEP TO COMPLETE REMEDY.
Bolt head will require a 5/8” wrench or socket.
Nut on the bolt will require an 11/16” socket.
Use a torque wrench (FT/LBS) and torque the nut end to 45 Ft/Lbs.
Mark the bolt with a white line as shown in photo to indicate the bolt has been torqued properly.
Replace the rubber boot back over the bolt.
INSTRUCTIONS – Embark, Reatta & Reatta XL (UPPER & LOWER bolts)
Both the upper and lower slip shaft bolts are located under the floor.
The generator slide compartment must be opened to access the slip shaft bolts.
Pull the generator slide manual release lever located in the electrical compartment beneath the driver side window (FIG 10).
Both bolts should be visible on the steering shaft, one above the steering U-joint and one below the steering U-joint.
FIG 8:
- This is the lower slip shaft bolt below the U-joint.
- If the bolt has been properly torqued at the factory there will be a white line running from the head of the bolt to the nut end of the bolt (arrow).
FIG 9:
- This is the upper slip shaft bolt which is directly above the U-joint shown in Fig 8.
- If the bolt has been properly torqued at the factory there will be a white line running from the head of the bolt to the nut end of the bolt (arrow).
IF THE WHITE LINE IS NOT VISIBLE PROCEED TO NEXT STEP TO COMPLETE REMEDY.
Bolt head will require a 5/8” wrench or socket.
Nut on the bolt will require an 11/16” socket.
Use a torque wrench (FT/LBS) and torque the nut end to 45 Ft/Lbs.
Mark the bolt with a white line as shown in photo to indicate the bolt has been torqued properly.
Repeat this torque procedure for both slip shaft bolts (if the white line is missing).
Affected Units: | Jayco 2019 Embark
K1NE0057-0061 K1NJ0057-0064 Entegra 2019 Anthem K14A8060-8061 K14B8098-8108 K14F8102-8104, 8107-8113 K14W8090, 8092-8096 Entegra 2019 Aspire K13B8086-8089, 8091, 8093 K13H8064-8067 K13M8067-8068 K13P8067 K13R8107-8110, 8112 K13W8080-8083 Entegra 2019 Cornerstone K16B8087-8089, 8091-8092, 8094 K16F8079-8080, 8082-8083 K16W8084-8088 K16X8061 Entegra 2019 Insignia K11B8053 K11P8053-8054 K11R8062 K11W8056 Entegra 2019 Reatta K1NE8064, 8066-8076 K1NG8055-8057, 8059-8061 K1NJ8058 Entegra 2020 Reatta XL L1MG8051 L1MJ8051 |
Retail Instructions to INSPECT THE LOWER STEERING SHAFT BOLT
- Turn the ignition ON (the engine does not need to be running)
- Make sure there is an unobstructed area 3 feet in front of the motorhome.
- Open the generator compartment using the switch (arrow) inside the driver side front electrical compartment. Press and hold the switch until compartment is fully extended.
- The steering shaft bolt is located on the right side of the generator behind the washer fluid bottle (arrow).
- Bolt location is circled in this photo.
- Arrow is pointing to the Steering Shaft bolt.
- Wiring harnesses may have to be moved aside to see it.
- If there is a white line running from the bolt head to the nut as shown in the photo (large arrow), this bolt is torqued to the proper specification.
- IF WHITE LINE IS NOT PRESENT – THE BOLT IS NOT TORQUED PROPERLY.
- CAUTION IS REQUIRED – do not drive your motorhome until you complete all inspection steps
- Close the generator compartment using the switch shown in Fig 1.
- Ignition must be ON to close the compartment (engine does not need to be running).
- Hold the switch, until the compartment closes completely.
PROCEED TO THE INSPECTION OF THE UPPER BOLT.
Retail Instructions to INSPECT THE UPPER STEERING SHAFT BOLT
- Upper steering shaft bolt is located on the steering column, beneath the steering wheel and under the large rubber boot.
- Lower the rubber boot on the steering column to see the bolt. FIG 7:
- Examine the upper steering shaft bolt (front and back of the steering column).
- If there is a white line running from the bolt head to the nut as shown in the photo (large arrow), the bolt is torqued to the proper specification.
- IF WHITE LINE IS NOT PRESENT – THE BOLT IS NOT TORQUED PROPERLY.
PROCEED TO THE PRECAUTION STEP BEFORE YOU DRIVE YOUR MOTORHOME
PRECAUTION STEP
The bolt threads visible in Fig 5 AND 6 ( for Upper and Lower bolts) must be at least two threads past the nut for the locking feature to be engaged, to ensure your safety to travel to a Dealer to have the bolt/s properly torqued at 45 ft. lbs.
If there are less than two threads showing past the nut, you must tighten with a 5/8” wrench on the bolt side / 11/16” on the nut size, till at least two threads are past the nut. This must be completed prior to moving your motorhome.
- Complete Reply Form and return to Jayco Compliance.
September 2019
Safety Recall:
19V-625 Jayco
19V-626 Entegra
IMPORTANT SAFETY RECALL
This Notice Applies to Your Recreational Vehicle «vin»
Dear Valued Customer:
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.
Jayco has decided that a defect, which relates to motor vehicle safety, exits in certain Model Year 2019 2020 Entegra Anthem, Aspire, Cornerstone, Insignia, Reatta and Reatta XL Class A Motorhomes and 2019 Jayco Embark Class A Motorhomes.
Reason for this | The upper and lower steering shaft bolt may not be torqued to 45 ft. /lbs. as specified. An unsecured bolt could allow the steering wheel not to function, affecting drivability and increasing the risk of a crash. |
Recall Remedy | Inspection is required for evidence that each bolt (2) is torqued to 45ft/lbs. A white line from the steering shaft bolt head to the nut confirms the bolt was torqued per specifcaitons and no further repair is required. The omittance of the white line notes the bolt was not properly torqued prior to shipping and Special Precautions are required prior to moving your motorhome. |
What we need you to do immediately | Please read and follow the enclosed Inspection Instructions and return the Reply
Form noting the results of the inspection. When applciable, contact an authorized Dealer to schedule an appointment to have this remedy completed free of charge. The recall remedy will take approxiamtly thirty minutes. |
If you had this repair completed prior to receipt of this recall notice, you may be eligible to receive reimbursement for the cost of obtaining a pre-notification remedy of the problem associated with this recall.
If you take your recreational vehicle to your dealer on the agreed service date and the dealer does not remedy this condition on that date or within three (3) days, please contact our Customer Service Department at 800-517-9137. If after contacting your dealer and Customer Service you are not able to have the safety defect remedied without charge and/or within a reasonable time, you may wish to submit a written complaint to the Administrator, national Highway Traffic Safety Administration, 1200 New Jersey Avenue, SE., Washington, DC 20590; or call the toll-free Vehicle Safety Hotline at 1-888-3274236 (TTY: 1-800-424-9153): or go to https://www.safercar.gov. Federal regulations require that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days.
We certainly regret this inconvenience; however, your safety is our most important priority.
Sincerely,
Jayco Motorized Division
IMPORTANT SAFETY RECALL
Safety Recall:
19V-625 Jayco
19V-626 Entegra
September 2019
Dear Valued Dealer:
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.
Jayco has decided that a defect, which relates to motor vehicle safety, exits in certain Model Year 2019 -2020 Entegra Anthem, Aspire, Cornerstone, Insignia, Reatta and Reatta XL Class A Motorhomes and 2019 Jayco Embark Class A Motorhomes.
Reason for this recall | The upper and lower steering shaft bolt may not be torqued to 45 ft. /lbs. as specified. An unsecured bolt could allow the steering wheel not to function, affecting drivability and increasing the risk of a crash. |
Recall Remedy | Inspection is required for evidence that each bolt (2) is torqued to 45ft/lbs. A white line from the steering shaft bolt head to the nut confirms the bolt was torqued per specifcaitons and no further repair is required. The omittance of the white line notes the bolt was not properly torqued prior to shipping and Special Precautions are required prior to moving the motorhome. |
All pertinent information regarding this recall is available under the Service and Parts Tab of our Website. If you need further assistance, please Contact Customer Service at 800-283-8267. | |
What we need you to do | Our records show the following unit is affected by this recall and is currently part of the inventory at your Dealership. The Recall Remedy must be completed on this unit prior to customer delivery. |
VIN
Federal law requires that all units in your inventory be repaired prior to delivery to a customer. If you have sold a unit recently that you have received a stock recall notice on, please contact the owner immediately to advise of the recall. In addition, please register the unit by submitting the Warranty Registration.
We certainly regret this inconvenience; however, our Customers’ safety is our most important priority.
Sincerely,
Jayco Motorized
10 Affected Products
Vehicles
MAKE | MODEL | YEAR |
ENTEGRA | ANTHEM | 2019-2020 |
ENTEGRA | ASPIRE | 2019-2020 |
ENTEGRA | CORNERSTONE | 2019-2020 |
ENTEGRA | INSIGNIA | 2019-2020 |
ENTEGRA | REATTA | 2019-2020 |
14 Associated Documents
Recall Quarterly Report #1, 2019-3
RCLQRT-19V626-1989.PDF 211.122KB
Recall Quarterly Report #4, 2020-2
RCLQRT-19V626-1167.PDF 211.41KB
Recall Quarterly Report #2, 2019-4
RCLQRT-19V626-6543.PDF 211.216KB
Recall Quarterly Report #3, 2020-1
RCLQRT-19V626-2556.PDF 211.3KB
Remedy Instructions and TSB
RCRIT-19V626-7707.pdf 710.413KB
Miscellaneous Document
RMISC-19V626-1211.pdf 576.338KB
Owner Notification Letter(Part 577)
RCONL-19V626-4923.pdf 51.342KB
Manufacturer Notices(to Dealers,etc)
RCMN-19V626-0677.pdf 190.356KB
Recall Acknowledgement
RCAK-19V626-2059.pdf 244.839KB
Defect Notice 573 Report
RCLRPT-19V626-1594.PDF 213.564KB
Miscellaneous Document – Retail Reply Form
RMISC-19V626-9900.pdf 561.044KB
Miscellaneous Document – RETAIL pre-notification Instructions
RMISC-19V626-2612.pdf 825.927KB
Miscellaneous Document – 2019-2020 Entegra AFfected units
RMISC-19V626-8172.pdf 131.223KB
Manufacturer Notices(to Dealers,etc)
RCMN-19V626-1127.pdf 674.009KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=19V626&docType=RCL
- Durable Ratchet Head: Made from Hardened treated Chrome Vanadium steel alloy (Cr-V) Corrosion-Retardant: Satin Finish. Made in Taiwan
- Easy Storage: A sturdy plastic storage case is included. Non-Slip Grip: Knurled handle
- Easy to Read: High Contrast & Dual Range Scale. Accurate: Pre-Calibrated to ± 4%
- Accessories included: 1/2" Drive 5" long Extension Bar and 1/2" Drive to 3/8" Drive Reducer
- Simple and Reliable: “Click” sound tells the preset torque value is reached. Stop applying force when you hear and feel it.
- PRECISION - Ships pre-calibrated to +/- 4% accuracy and ready to use. Include calibration certificate with traceable serial number.
- DURABLE - Reinforced ratchet gear head constructed from hardened, heat treated Chrome Vanadium alloy steel.
- LONG-LASTING - Rust & corrosion protection with our unique and newly invented Electro-Black finish treatment.
- PERFORMANCE - Features an easy-to-read, highlighted yellow print dual-range scale. Identify the markings even in low-light conditions.
- COMFORTABLE - Comes with a reversible ratchet head that drives in both directions and measure torque in a clockwise direction.
- ±3% HIGH PRECISION AND COOL APPEARANCE: 1/2 inch drive torque wrench (10-170ft.-lb/13.6-230.5Nm)has a calibration error range of ±3%, high precision, and comes with a corresponding serial number, which is easy to trace the original data, and you can use it with confidence.Hairich torque wrench not only has superior quality but also has a superior appearance. The classic combination of black and red is fashionable and textured, allowing you to enjoy a visual feast during use.
- PREMIUM MATERIAL AND DURABLE: Experience the ultimate durability and antiskid with the torque wrench. The main body of Hairich torque wrench set is made of chrome vanadium steel alloy, which is more strong and more durable. The head of the inch-pound torque wrench adopts a ratchet design with a reversing device to improve work efficiency. The square knurled handle is made of aluminum titanium alloy, which is ergonomic and comfortable to hold for long-time use.
- DUAL SCALE AND QUICK SETTING: Laser Printed by dual-range(ft-lb and Nm). Our professional torque wrench is easy to read and provides direct unit conversion, When the set torque value is reached, the torque wrench will make an audible and felt click to remind you to stop applying force. Pull down the lock knob and hold it until the torque setting is completed. Release the hand, and the lock knob will automatically rebound back to lock the value.
- ERGONOMIC DESIGN AND POWERFUL: Every design of our industrial torque wrench conforms to ergonomic, easy to handle.72-tooth ratchet, 5° ratcheting arc head, a quick-release button for easy loading and unloading, and an aluminum non-slip handle for excellent grip and control. A recent research review that, 72-tooth ratchets are very professional tooth ratchets, you just only rotate 5 degrees to finish it. Not easy to slip and wear, can be used in small spaces, and is more durable and powerful.
- EASY OPERATION AND SAFETY: Thanks to its bidirectional drive ratchet head, our torque wrench can be measured both clockwise and counterclockwise. When the set torque value is reached, a "click" sound will remind you to stop applying force to prevent damage to the item due to excessive torque. Notice: At low Nm settings under 5 Nm the "click" sound can be too light to hear.
- 【High Precision&Quick Reading】: 3/8 torque wrench has high contrast and dual range scale( 5-45 Ft-Lb/6.8-61 Nm),making it clear and easy to read. We have professional torque wrench production technology, and after 20000 tests, the calibration error range of the torque wrench is ± 3%, making it an essential helper for you.
- 【Safe and Reliable Operation】: Equipped with a bidirectional drive ratchet head, torque can be measured clockwise or counterclockwise. When the set torque value is reached, a "click" sound will remind you to stop applying force to prevent damage to the item due to excessive torque.
- 【High Quality and Durable Material】: Made of hardened chromium vanadium steel alloy (Cr-V). At the same time, the bottom buckle tail plug adopts a red anodizing process to improve the product's oxidation resistance during use and enhance surface wear resistance. 72 tooth ratchet head, made of chromium molybdenum steel. High quality materials resist corrosion and are durable.
- 【Quick Torque Setting】: Simple and fast torque setting, pull down the locking knob and hold it down to rotate to the torque you need. Release the hand and the locking knob will automatically rebound to lock the torque value. And the designer referred to the appearance of the flashlight handle and designed a non slip and labor-saving knurled handle, making it more comfortable and easy to hold when using.
- 【Easy to Store and Widely Use】: You will receive the 3/8-inch drive click torque wrench with a sturdy plastic shell storage box, which is very delicate and durable. Torque wrench is suitable nuts and bolts on various occasions, such as bike, motorcycle, car spark, and is the best helper for you🎁. 🔔 And we provide 12 months warranty. If you have any questions, please feel free to contact us.
- 【3Pcs Torque Wrench Set】 The calibration error range is ±3%, each torque wrench has a calibration certificate. The 3-in-1 torque wrench set can meet your different needs. Including 1/4 inch 20-240in.lb, 3/8 inch 5-45ft.lb, 1/2 inch 20-160ft.lb.
- 【Safe & Reliable】 When the 1/2 torque wrench reaches the preset torque value, it makes a clear "click" sound, accompanied by an obvious hand vibration that reminds you no longer to apply force, prevent damage caused. 72-tooth reversible ratchet head, it can be used both clockwise and counterclockwise directions.
- 【Quick Release Button】 This 3/8 torque wrench has a quick release button with which accessories can easily be installed and removed, the accessories can grip and is not easy to fall down. It is more convenient to use. The torque wrench is made of CR-MO with a higher hardness.
- 【Easy to Set】First pull down the locking knob and hold it down and then start setting the desired torque value. Release the hand and the locking knob will automatically rebound to lock the torque value. If you do not use, please set the torque key to the minimal torque value.
- 【Widely Use】The torque wrenches can satisfy you in bicycle, motorcycle, car, truck and wheel screws, wheel nuts and in the device installation, electrical engineering, etc. We provide 12 months warranty. If you have any questions, please feel free to contact us.
- PORTABILITY: Torque wrench 1/2 inch drive has a durable case for portability or storage
- ADDED COMFORT: Bi-material handle for comfort and grip of the 1/2 torque wrench
- HASSLE FREE USE: Locking feature adjusts quick and easily for hassle free use
- QUICK IDENTIFICATION: Scales stamped into housing showing inch and metric torque settings
- Meets or Exceeds ASME Specifications
- 🔧【𝐌𝐢𝐥𝐢𝐭𝐚𝐫𝐲-𝐠𝐫𝐚𝐝𝐞 𝐒𝐭𝐞𝐞𝐥】ETOOLAB torque wrench utilizes military-grade steel as its base material, coupled with professional surface rust protection methods tailored to usage habits. While ensuring user comfort, it enhances product strength, wear resistance, and rust resistance. offers a more comfortable experience and a longer lifespan!
- 👍【𝐄𝐚𝐬𝐲-𝐭𝐨-𝐑𝐞𝐚𝐝】The scale of this 1/2 drive torque wrench is laser-engraved, using a black background with white markings. dinamometrica de 1/2 ensures clear and easy readability of the scale, even in sunlight. With a dual-scale design, users can conveniently read torque values in two different units according to their preferences, without the need for conversion!
- ⚙️【±𝟑% 𝐏𝐫𝐞𝐜𝐢𝐬𝐢𝐨𝐧 & 𝐒𝐢𝐦𝐩𝐥𝐞 𝐋𝐨𝐜𝐤𝐢𝐧𝐠 𝐑𝐢𝐧𝐠】Our torque wrench 1/2 drive meets the high precision standard of ±3% and comes with a traceable serial certificate. You can use it with confidence! Moreover, its graduation ring is tightly locked, with smaller incremental values, ensuring precise and consistent torque output even after multiple uses. This reduces the hassle of frequent adjustments. It is undoubtedly an excellent tool for your work!
- 🔊【𝐋𝐨𝐮𝐝 𝐂𝐥𝐢𝐜𝐤 𝐒𝐨𝐮𝐧𝐝】This torque wrenches has been upgraded to have a louder "Click" sound. We conducted over 25,000 tests to ensure that each product produces a click sound volume of no less than 45dB when the torque value exceeds 34 lbf·ft. When you hear the distinct click sound, it indicates that the preset torque has been reached, signaling you to stop applying force. You no longer need to worry about damaging your mechanical components.
- 💯【𝐔𝐬𝐞𝐫-𝐅𝐫𝐢𝐞𝐧𝐝𝐥𝐲】Our torque wrench set features a 72-tooth dual-directional ratchet head, allowing for easy operation in both clockwise and counterclockwise directions. It is designed with an adjustable locking ring, making it effortless to adjust the preset torque value. Additionally, it includes a quick-release head design, allowing it to replace the wrench head accessories more easily!
- Includes 1-pc. 3/8 in. drive torque wrench; Storage case; Product manual with torque conversion chart
- Wrench emits a click that can be heard and felt when the preset value is reached
- Permanently marked, high-contrast dual-range scale is easy to read, even in low light
- Reversible ratchet head drives in both directions and measures torque in clockwise direction
- Durable all-steel construction has no plastic parts to break or wear out
- Includes 1-pc. 1/4 in. drive micrometer torque wrench (20-200 in.-lb.) with storage case and product manual; 1-pc. 3/8 in. drive micrometer torque wrench (10-80 ft.-lb.) with storage case and product manual; 1-pc. 1/2 in. drive micrometer torque wrench (25-250 ft.-lb.) with storage case and product manual
- Wrenches emit a click that can be heard and felt when the preset value is reached
- Permanently marked, high-contrast dual-range scale is easy to read, even in low light
- Reversible ratchet heads drive in both directions and measure torque in clockwise direction
- Durable all-steel construction has no plastic parts to break or wear out
- 【PRECISION】 - Ships pre-calibrated to +/- 4% accuracy and ready to use. Include calibration certificate . Before shipping, we take 200 times calibration tests to make sure all wrenches performance well .
- 【DURABLE】 - Reinforced ratchet gear head constructed from hardened, heat treated Chrome Vanadium alloy steel.
- 【 RELIABLE & SAFE】: When small torque wrench set torque value is reached, the wrench will emits slight click sound to remind you to stop applying force to prevent overtorque damage to your items.
- 【LONG-LASTING】 - Rust & corrosion protection with our unique and newly invented Chrome finish treatment.
- 【 DUAL-DIRECTION MEASURES & WIDE USE】: The paddle of the mini torque wrench head can adjust the direction of use at any time,so that the wrench can be used both clockwise and counterclockwise directions. More widely used for Installation equipment, Electrical engineering, bicycle/motorcycle maintenance, Product assembly.With a storage box and an instruction manual.
Last update on 2024-04-11 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.