NHTSA ID Number: 10161734
Manufacturer Communication Number: SCI18-47A
Summary
This procedure is to guide you through the steps required to adjust the slide out room laterally in the frame opening, Front and rear from a vehicle standpoint.
1 Affected Product
Vehicle
| MAKE | MODEL | YEAR |
| PREVOST | H3-VIP | 2019 |
DESCRIPTION
This procedure is to guide you through the steps required to adjust the slide out room laterally in the frame opening, Front and rear from a vehicle standpoint.
We are aiming for an even lateral gap on each side of the slide-out room. We will start by loosening the elements preventing lateral movement of the slide-out. Once this is done we will use the adjustment tool (See Special Tools below) to slightly move the slide-out. Upon reaching the desired gap, we will tighten each element to preserve the adjustment.
Prevost Technical Publications
Writer: <fl QF7720955 rev 7>
i
SERVICE CENTER INFORMATION
SCI18-47A
DATE :
February 2019
SECTION : 26 SLIDE-OUT
SUBJECT :
SLIDE OUT LATERAL ADJUSTMENT
Revision: A
Added tool number
06-26-2019
APPLICATION
Model
VIN
H3-45 VIP motorhomes
Model Year : 2019 -
From 2PCV33496KC710295 up to -
DESCRIPTION
This procedure is to guide you through the steps required to adjust the slide out room laterally in the frame opening, Front and rear from a vehicle standpoint.
We are aiming for an even lateral gap on each side of the slide-out room. We will start by loosening the elements preventing lateral movement of the slide-out. Once this is done we will use the adjustment tool (See Special Tools below) to slightly move the slide-out. Upon reaching the desired gap, we will tighten each element to preserve the adjustment.
SPECIAL TOOLS
Slide-out lateral adjustment tool G36187, drive with a 24mm socket.
MATERIAL
No parts are required:
SCI18-47A
Page 2 / 4
Writer: <fl QF7720955 rev 7>
PROCEDURE
DANGER
Park vehicle safely, apply parking brake, stop engine. Prior to working on the vehicle, set the ignition
switch to the OFF position and trip the main circuit breakers equipped with a trip button. On Commuter
type vehicles, set the battery master switch (master cut-out) to the OFF position.
1. With the slide-out extended, loosen these
retaining screws, both sides.
Figure 1
2. Measure the existing lateral gaps.
Values:
Left_____________
Right____________
3. Release pressure on the upper stopper by
moving the room slightly outwards, about 3/4”.
4. The top of the slide-out should be free and the
upper stopper released from the structure key.
SCI18-47A
Page 3 / 4
Writer: <fl QF7720955 rev 7>
5. Under the slide-out, on one of the drive shaft
yokes, loosen two set screws
Figure 2: Drive shaft set screws
6. Loosen screw H one quarter turn (¼ t)
7. Loosen screw 1 half a turn (½ t).
8. Loosen screw 2 half a turn (½ t).
9. Do this on both sides of the room.
Figure 3 : H : height; 1 & 2 : retaining screws
10. Insert tool G36187 in cavity.
Figure 4
SCI18-47A
Page 4 / 4
Writer: <fl QF7720955 rev 7>
11. Turn tool with a ratchet and 24mm socket to
adjust.
12. Check gaps.
13. Proper gap is 9 mm ±2 mm.
14. Work to have an equal distribution of the gap
on both sides.
Figure 5
15. Tighten screw 1 to 59 lb-ft (80Nm).
16. Tighten screw 2 to 59 lb-ft (80Nm).
17. Tighten the height screw H to 59 lb-ft (80Nm).
18. Tighten the jam nut on screw H to
43 lb-ft (58Nm).
19. Do this on both sides of the room.
Figure 6
20. Tighten the retaining screw to
59 lb-ft (80Nm).
21. Do this on both sides of the room.
Figure 7
22. Confirm proper operation of the slide-out.
SCI18-47A
February 2019
https://www.nhtsa.gov/recalls?nhtsaId=10161734
https://static.nhtsa.gov/odi/tsbs/2019/MC-10161734-0001.pdf
Loading...
Reload document 
Open in new tab
- Impact pieces are constructed of heavy-duty drop-forged premium chrome vanadium steel to withstand extreme levels of torque changes against fasteners
- 6-Point hex socket design prevents round-off deterioration under high torque and hammering stress with use of impact and electric wrenches
- Highly visible laser-etched markings on corrosion-resistant black phosphate finish makes it easy to identify drive socket sizes, specs, and measurements
- Sturdy and strong blow molded case features socket size labels for organized storage and is secured by two lever locks
- The complete set comes with the following pieces: 58 x 1/2" Drive sockets - SAE (Deep and shallow): 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1, 1-1/16, 1-1/8, 1-1/4", metric (Deep and shallow): 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24mm; 3 x 1/2" Extension bars: 3, 5, 10-inch, 1 x 1/2" By 10-inch length quick-release ratchet handle 72-tooth, 1 x 1/2" Impact universal joint, 1 x 1/2" (F) to 3/8" (M) reducer, 1 x 3/8" (F) to 1/2" (M) Adapter
- 【HEAT TREATED CR-V】: KBOISHA industrial grade impact socket set adopt higher quality chrome vanadium steel. After heat treatment and forging, it has high hardness and good toughness. Flexible for impact wrench and other high torque tools.
- 【6-POINT DESIGN】: Special internal arc angle design of 6-point socket increases the contact area with the fasteners, grasp more firmly. Protect nut from wear and skid.
- 【HIGH DURABILITY】: The surface is black phosphate finish to prevent the socket from rusting,and corrosion resistant, extend the service life. Can remove fasteners at least ten thousand times.
- 【DOUBLE SIZE MARK】: The laser mark on the impact socket and the specification mark on the tool box make it easy to quickly identify the socket you need. It is suitable for the installation and repair of automobile, machinery, equipment and other products.
- 【COMPLETE CONFIGURATION】: With a heavy toolbox, convenient to storage and carry, include: 1/2" drive 15 x metric sockets;15 x Deep sockets; 14 x SAE sockets; 14 x Deep SAE sockets. 3",6",10" drive impact extension bar, 2 x 1/2" universal joint,and a ratchet handle. The workmanship exceeds the ASME and ANSI standards.
- LIFETIME WARRANTY WITH SUNEXPRESS: Get in the express lane with the industry’s leading warranty program and exchange warranted products directly with Sunex.
- CR-MO STEEL: Provides the strength and flexibility to handle high torque impact tools.
- RADIUS CORNER DESIGN: Reduces wear and increases torque on fasteners by placing force on fastener walls rather than fastener corners.
- CHAMFERED OPENING: Quickly aligns fastener to socket.
- DUAL SIZE MARKINGS: Laser etched and roll stamped markings to ensure permanent socket identification.
- Impact pieces are constructed of heavy duty drop-forged premium chrome vanadium steel to withstand extreme levels of torque changes against fasteners
- 6-point hex socket design prevents round-off deterioration under high torque and hammering stress with use of impact and electric wrenches
- Highly visible laser-etched markings on corrosion resistant black phosphate finish makes it easy to identify drive socket sizes, specs, and measurements
- Sturdy and strong blow molded case features socket size labels for organized storage and is secured by two lever locks
- The complete set comes with the following pieces: (28) 1/2-inch drive sockets SAE: 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1-inch, 1-1/16-inch, 1-1/8-inch, 1-1/4-inch METRIC: 10, 11, 12, 13, 14, 15, 17, 19, 21, 22, 24, 27, 30, 32mm, (3) 1/2-inch drive extension bars: 3, 5, 10-inch, (1) 1/2-inch drive 10-inch quick-release ratchet handle, (1) 1/2-inch drive impact universal joint, (1) 1/2 to 3/8-inch drive impact reducer, (1) 3/8 to 1/2-inch drive impact adapter
- LIFETIME WARRANTY WITH SUNEXPRESS: Get in the express lane with the industry’s leading warranty program and exchange warranted products directly with Sunex.
- CR-MO STEEL: Provides the strength and flexibility to handle high torque impact tools.
- RADIUS CORNER DESIGN: Reduces wear and increases torque on fasteners by placing force on fastener walls rather than fastener corners.
- CHAMFERED OPENING: Quickly aligns fastener to socket.
- DUAL SIZE MARKINGS: Laser etched and roll stamped markings to ensure permanent socket identification.
- Lifetime with sunexpress: get in the Express lane with the industry’s leading program and exchange warranted products directly with Sunex.
- Double deep: Allows for better access over long studs.
- Flip Sockets: Two bonus deep flip sockets for quickly removing common lug nut sizes.
- Cr-mo steel: provides the strength and flexibility to handle high torque impact tools.
- Radius corner design: reduces wear and increases torque on fasteners by placing force on fastener walls rather than fastener corners.
- The 1/2 in. Drive Master Impact Socket Set is a complete collection of most frequently used impact sockets and accessories, organized in one convenient impact-resistant tool case
- Premium Chrome Molybdenum steel tempered with our proprietary heat treatment process to withstand more torque from power tools
- Expertly coated with manganese phosphate, the preferred coating in military and aerospace, which offers superior protection and corrosion resistance compared to black oxide coating on other impact sockets
- 6-point WaveDrive design grips fasteners more tightly than traditional design, preventing fastener rounding and giving you more leverage
- 61-piece set includes (28) 1/2 in. drive standard impact sockets, (28) 1/2 in. drive deep impact sockets, (4) 1/2 in. drive impact extension bars, (1) 1/2 in. drive impact universal joint
- Made from drop forged and heat treated chrome vanadium steel (50BV30) with a corrosion-resistant black phosphate finish, providing the durability for a hard use. High-contrast laser etched with high-visibility markings and hard stamped with size labels.
- Set includes deep 6-point sockets : SAE: 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1, 1-1/16, 1-1/8, 1-1/4", Metric: 10, 11, 12, 13, 14, 15, 16, 17, 19, 21, 22, 24, 27, 30, 32mm;
- Set includes: 1/2" Extension bars: 3, 5, 10-inch, 1/2" By 10-inch length quick-release ratchet handle 72-tooth, 1/2" Impact universal joint, 1/2" (F) to 3/8" (M) reducer, 3/8" (F) to 1/2" (M) three way Adapter
- Heavy duty plastic blow-molded carrying case for easy transport, simple storage, and quick organization.
- Meets or exceeds ANSI performance standards. It comes with 1 year quality warranty.
- CR-MO alloy steel for long life
- Most complete 1/2 inch drive metric 12 point set available
- Heavy duty blow molded storage case
- 12 Point sockets offer double the starting points as 6 point sockets
- Set includes 19 standard sockets, 19 deep sockets and 1 universal joint
- [Impact Sockets] crafted with aerospace grade steel for power and flexibility in demanding high torque impact tools
- [Master Set] Our Largest 1/2" Drive Socket Set Ever! 70pc of every tool we have ever needed in a 1/2" drive socket set, including a ratchet handle. Too many to list here, see Product Description below for a list!
- [Radius Corner Design]: Sockets designed to apply more force and reduce rounding of bolts by grabbing fasteners by their sides, not tips.
- [Faster fastener gripping]: Sockets design with a chamfered opening to align faster and make fastener gripping smooth as possible.
- [Lifetime Warranty]: Best in category warranty! Break a single socket? Don’t send back your whole set and wait on a replacement for weeks. We pride ourself on quick and efficient replacements by sending out just the socket(s) that broke. Pretty cool, huh?
Last update on 2021-01-24 / Affiliate links / Images from Amazon Product Advertising API
Last update on 2021-01-24 / Affiliate links / Images from Amazon Product Advertising API
