Loss of Drive from Fractured Pressure Switch – Allison Transmissions

“This site contains affiliate links for which OEMDTC may be compensated”

NHTSA Campaign Number: 18E085
Manufacturer Allison Transmission, Inc.
Components POWER TRAIN
Potential Number of Units Affected 566

 

Loss of Drive from Fractured Pressure Switch

A loss of drive can disable the vehicle unexpectedly, increasing the risk of a crash.

 

Summary

Allison Transmission, Inc. (Allison) is recalling certain H 50 EP, H 40 EP, H 50 Cert, and H 40 Cert Drive Units. The pressure switches on these Drive Units may fail, possibly resulting in a loss of drive.

 

Remedy

Allison will notify the vehicle manufacturers that purchased the affected transmissions, and dealers will replace the C1 and C2 pressure switches, free of charge. Owners may contact Allison customer service at 1-800-252-5283.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 


Revisions to this document are noted by a stripe in the left-hand margin

2018FA07, Rev. B
September, 2018

 

SUBJECT: H 40/50 EPTM Drive Unit C1/C2 Pressure Switch

MODELS AFFECTED: H 40/50 EPTM Drive Unit

 

Introduction:

Allison Transmission, Inc. (ATI) has identified an issue with the pressure switch (P/N 29506484) used in a specific population of H 40/50 EP Drive UnitsTM. The Drive Units, within the serial number range specified below, were built with pressure switches that can fail in an either open or closed state. The failure can cause diagnostic trouble codes (DTCs) to set which may disable the corresponding clutch, locking the Drive Unit into the unaffected range with reduced performance, or disable propulsion. Additionally, a subset population of Drive Units within the same serial number range may have debris in valve bodies or internal passages that could prevent proper valve operation. The purpose of this Field Action is to proactively replace the two (2) pressure switches used in each of the affected Drive Units, and inspect and remove debris in the subset population according to the procedure included in this Field Action.

Prior to working on vehicles, please read SIL 21-TR-18, Defective Normally Open Pressure Switch P/N 29506484, for parts information. All replacement pressure switches installed in the affected Drive Unit serial number ranges must be stamped with a date code of 1918 or later.

 

Serial Number Range:

The serial number range included in this Field Action is 7110008855 through 7110009446. All serial numbers in this range will require the two (2) pressure switches to be replaced.

The serial numbers of the subset population requiring the additional debris inspection and removal are 7110009294 through 7110009445.

 

Repair Process Overview:

All buses equipped with a Drive Unit serial number 7110008855 through 7110009446 will need to have the oil drained into a clean container for reuse. The oil pan will be removed and the two (2) pressure switches replaced. Refer to Allison Electric Drives Service Manual SM3602 Section 5-12 for pan removal and Section 6-15, C1/C2 Relay Valve Body, for switch replacement.

For buses equipped with a Drive Unit serial number 7110009293 through 7110009445, valve bodies will need removed, inspected for debris, and compressed air blown through the C1 and C2 pressure taps in the rear cover to remove any potential debris, followed by pressure switch replacement. Instructions for Drive Unit serial numbers

7110009293 through 7110009445 are provided at the end of this document. Refer to Allison Electric Drives Service Manual SM3602 Sections 5-13 through 5-17 for disassembly and Sections 6-13 through 6-15 for installation.

 

Table 1. ATI Required Service Parts

Part Description Part Number Quantity Per Bus
Pressure Switch, N/O 29506484 2
O-Ring, Switch 29501439 2
Gasket, Oil Pan 29538847 1
O-Ring, Drain Plug 23019664 1
O-Ring, Filter 23018950 1

 

Claim Submittal Information:

For all proactive repairs, refer to Table 2 and Table 3 below for claim submittal information.

For all claims made against repairs that are not proactive; where a pressure switch is already failed before it could be pro-actively replaced, refer to Table 4 and Table 5 below for claim submittal information.

 

Table 2. Proactive Repair Claim Information

Claim Type 04
Special Activity Indicator 2018FA07
Primary Failed Part 29506484
Complaint Code AT02
Failure Code CC03

 

Table 3. Proactive Repair Labor Codes

Labor Code Labor Hours Labor Operation
00094100 1.2 R&R Oil Pan and Fluid
00096100 0.2 Switch Replacement
00094700 2.8 Debris Inspection
00096400 0.5 Final Test Drive

 

Refer to Table 4 and Table 5 below for non-proacitve repair claims.

 

Table 4. Non-Proactive Repair Claim Information

Claim Type 01
Special Activity Indicator 2018FA07
Primary Failed Part 29506484
Complaint Code EL02
Failure Code AC00

 

Table 5. Non-Proactive Repair Labor Codes

Labor Code Labor Hours Labor Operation
00094100 1.2 R&R Oil Pan and Fluid
00096100 0.2 Switch Replacement
00094700 2.8 Debris Inspection
00096400 0.5 Final Test Drive
00096901 0.5 Troubleshooting and Diagnostics

 

Any additional parts, labor, net items, or travel costs deemed necessary to complete this Field Action must be described in detail in the claim narrative. Unexplained costs will be deducted from the claim.

Authorized Allison service outlets must follow the published Allison Transmission current labor time guide for work performed when adding any additional charges.

 

Procedure for Inspection and Removal of Debris:

  1. With the Drive Unit installed, drain the fluid into a clean container for reuse, and drop the oil pan from the Drive Unit.

drop the oil panFigure 1.

 

  1. suction filter and unplug all connectors on the internal harness.

suction filterFigure 2.

 

  1. oil level sensor, C1/C2 valve body, shift relay valve body, control main valve body, and separator plate.

oil level sensorFigure 3.

 

  1. C1 and C2 plugs (shown below) on the backside of the rear cover.

C1 and C2 plugsFigure 4.

 

  1. Starting with the C2 pressure circuit, plug the 4mm orifice on the stator housing, as shown below. Pressurize the C2 pressure tap on the rear cover with air to blow out any debris. Check the previously plugged 4mm passage for loose debris and remove if any is found.

C2 pressure circuitFigure 5.

 

  1. To inspect the C1 pressure circuit, plug the 4mm orifice on the opposite side the stator housing, as shown below. Pressurize the C1 pressure tap on the rear cover with air to blow out any debris. Check the previously plugged 4mm passage for loose debris and remove if any is found.

C1 pressure circuitFigure 6.

 

  1. Inspect the removed valve bodies and the separator plate for any machine chips or debris. Verify proper valve movement. If any debris is found, additional valve body teardown should be performed. Replace any components that may have damage.
  2. Reassemble the valve bodies and install two (2) new pressure switches (P/N 29506484) and O-rings (P/N 29501439). New switches must be stamped with date code 1918 or later on the metal retainer ring.

C1 pressure circuitFigure 7. Date Code Format

 

  1. Reassemble remaining parts, refill the Drive Unit, and test drive to verify proper operation.

*** IMPORTANT SAFETY RECALL ***
NHTSA Recall No. (18E085)

 

September ##, 2018

Dear [OEM]:

Allison Transmission Inc. (ATI) has identified an issue with the pressure switch (P/N 29506484) used in a specific population of H 40/50 EP Drive UnitsTM. The affected Drive Units are within the serial number range 7110008855 through 7110009446.Due to an out-of-specification material condition at the pressure switch supplier, the plastic molding used in the switch assembly may fracture. This condition may result in a failure of the pressure switch in either an open or closed state, triggering a diagnostic trouble code. In some circumstances, switch failures in the closed position can potentially disable propulsion at any time during a drive cycle without the ability to regain propulsion, presenting an increased risk of a vehicle accident and/or risk related to offloading passengers in the roadway.

ATI has upgraded the previously released Field Action 2018FA07 to a formal safety recall. (Please refer to Field Action 2018FA07, Rev. A.) A 573 Defect Notification was submitted to NHTSA on August 20, 2018. (Copy attached.)

Attached is a list of serial numbers shipped to [OEM] within the affected range. ATI’s authorized service network will be utilized to replace the C1 and C2 pressure switches used in each affected drive unit at no charge to the customer or [OEM]. ATI expects the repair time to range from 1.2 to 4.0 hours, excluding vehicle and shop logistics.

For drive units installed in vehicles that have left your control, we encourage you to make a safety defect determination in accordance with 49 USC 30118 et seq. and, as appropriate, to submit a Defect Notification to NHTSA in accordance with 49 CFR Part 573. At your option, ATI will conduct the recall, including notifying owners pursuant to 49 CFR Part 577 and performing the remedy.

If [OEM] desires to conduct the owner notification, please advise your ATI OEM Account Manager. ATI would like to review the letter prior to customer distribution. Attached is a copy of ATI’s owner notification letter, which has been approved by NHTSA. If [OEM] would like ATI to handle owner notification, we request the following information be provided no later than September 10, 2018:

  • Customer Name
  • Mailing Address
  • Vehicle Identification Number
  • Contact Information
    • First Name
    • Last Name
    • Position
    • Email
    • Phone

 

Please note that Federal law prohibits delivery of these drive units, or vehicles equipped with these drive units, under a sale or lease until this condition has been remedied.

If there are questions regarding this letter, please direct them to the following main point of contact:  Allison Transmission Inc. | One Allison Way | Indianapolis, IN 46222-3271

 

Larry Hansen
Director, Field Performance Evaluations
larry.hansen@allisontransmission.com
317-242-3712

 

Regards,

Corey Hudson
OEM Account Manager
corey.hudson@allisontransmission.com
317-756-1426

 

cc: Copy of ATI’s Part 573 Defect Notification
ATI Owner Notification Letter


2018FA07, Rev. B
September, 2018

https://static.nhtsa.gov/odi/rcl/2018/RCRIT-18E085-7640.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [1.10 MB]

 


2018FA07, Rev. A
August, 2018

https://static.nhtsa.gov/odi/rcl/2018/RCRIT-18E085-8692.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [1.09 MB]

 


Manufacturer Notice

https://static.nhtsa.gov/odi/rcl/2018/RCMN-18E085-5013.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [94.40 KB]

 


Recall Acknowledgement

September 13, 2018

https://static.nhtsa.gov/odi/rcl/2018/RCAK-18E085-2900.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [232.60 KB]

 


 

SaleBestseller No. 1
Allison Transmissions: How to Rebuild & Modify (Workbench How-to, SA540)
  • Garrett, Steve (Author)
  • English (Publication Language)
  • 144 Pages - 02/16/2023 (Publication Date) - Cartech Inc (Publisher)
Bestseller No. 2
Castrol TranSynd 668 Allison 2021 Updated SPEC 1 Gallon ONLY by DOXA Worldwide
  • Delivers improved gear protection.
  • Delivers extended anti-shudder durability.
  • Delivers extended clutch-friction durability.
  • Excellent corrosion and foaming resistance.
  • Excellent thermal and oxidative stability that helps to prevent deposits and oil thickening.
SaleBestseller No. 3
Allison 29539579 Screw-on Filter with Magnet Filter Kit replacing filter for Allison transmission per OEM Specs
  • Genuine Allison replacement spin-on external filter 29539579 and magnet.
  • Allison recommends changing this spin-on filter after initial 5,000 miles of us
  • The magnet is required to be changed with the filter to capture possible particulates in oil.
  • This Allison genuine spin on filter is one of the most widely used and recommended oil filters for the Allison 1000/2000 transmission.
Bestseller No. 4
Allison External Spin On Filter - 29539579 Multipack (Pack of 2)
  • Genuine Allison Transmission 29539579 Filter
  • Commonly found on on GMC and Chevy trucks with a Duramax engine
  • Fits Allison 1000, 2000, and 2400 series transmissions
  • Made in the USA
Bestseller No. 5
29549684 Automatic Transmission Fluid Pan Gasket Replacement for Allison LCT 1000/2000 Series 29536526
  • 【Wide Application】Automatic transmission fluid pan gasket is compatible with 2001-2019 6.6L Duramax LB7 LLY LBZ LMM LML L5P Allison applications, and also fits for GM vehicle systems including automatic transmission/transaxle, manual drivetrain and axles.
  • 【Fitment】Fits for GMC- 2007-2019 Sierra 3500 HD, 2007 Sierra Series, 2001-2019 Sierra 2500 HD, 2001-2006 Sierra 3500. Chevrolet- 2007-2019 Silverado 3500 HD, 2007 Silverado Series, 2001-2019 Silverado 2500 HD, 2001-2006 Silverado 3500. Replaces part number: 29549684 29536526.
  • 【High Quality Material】Automatic transmission fluid pan gasket is made of high quality steel, provides durability and sturdiness performance, with corrosion and impact resistant features, well make for long term reliable service.
  • 【Easy to Install】Automatic transmission fluid pan gasket is specially designed for your GM vehicle, its form, function and size get closer to the original part. When you replace your old or broken automatic transmission fluid pan gasket, you just need to simply change, saves your time, and provides affordable price for you.
  • 【100% Satisfaction Guarantee】If you have any questions about our automatic transmission fluid pan gasket, please contact us at first time.We are glad to solve the problem you meet and we support refund within 30-Day guarantee, 12-Month warranty for quality-related issues.
Bestseller No. 6
Castrol TranSynd 668 Allison 2021 Updated SPEC CASE of 3 by DOXA Worldwide
  • Delivers improved gear protection.
  • Delivers extended anti-shudder durability.
  • Delivers extended clutch-friction durability.
  • Excellent corrosion and foaming resistance.
  • Excellent thermal and oxidative stability that helps to prevent deposits and oil thickening.
Bestseller No. 7
Allison Transmission Transmission Filter for 2020-2021 Freightliner MT45 - 29539579
  • Genuine Allison Transmission Filter
  • Fits all 2001-2018 GM trucks equipped with Allison transmission
  • Fits all vehicles equipped with an Allison 1000, 2000 or 2400 series transmission
Bestseller No. 8
ANODZU Transmission Filter Kit Fits for Allison 3000-4000, 6 Inch Includes Gaskets and O-Rings, Replace 29548988 29558118 29558329 P560971
  • Compatible with: Transmission Filter Fits for Allison 3000-4000; Replaces Part Numbers: 29558329, 29548988, 29540494, 29545779, 29526898, P560971, Fleetguard, HF28943, PT9415-MPG KIT, AT327883, 2950 6337, 10059480, 57740, 57740XE, C9031
  • Material: Made of titanium steel frame and glass fiber filter material, excellent filtration performance, oil-proof, waterproof, can work under high temperature and low temperature environment, flame retardant, antistatic, corrosion resistant
  • Function: Filter iron filings, sediment and other impurities in the transmission oil, keep the transmission oil clean and supply each component, and improve the performance and service life of the transmission
  • How to Use: Directly replace the transmission filter that needs to be replaced, easy to operate and easy to install
  • Product Parameters: Gearbox filter*2, replacement gasket kit*1
Bestseller No. 9
GM Genuine Parts 29542833 Automatic Transmission Fluid Filter
  • Has an air-tight seal that virtually eliminates loss of line pressure
  • Has felt filter media that helps deliver high-filtration efficiency, excellent fluid flow, and long filter life
  • Has filter fibers that are infused with phenolic resin, adding strength and the ability to withstand fluid temperatures at the highest level of the transmission's normal operating range
  • Fits: 2011-2019 GMC Sierra 3500 HD,2011-2019 GMC Sierra 2500 HD,2011-2019 Chevrolet Silverado 3500 HD,2011-2019 Chevrolet Silverado 2500 HD
Bestseller No. 10
Genuine Allison Filter Kit 2001-2010 - Internal Shallow Filter (29537965) AND External Spin On Filter (29539579)
  • Fits Light Duty trucks 2001-2010 5 & 6 speed Allison 1000 Transmissions with the factory shallow pans
  • Genuine Allison Internal Shallow Filter - 29537965
  • External Spin On Filter (29539579)
  • Does not include pan gasket as it is reusable many times over.
  • DOES NOT FIT DEEP PANS

Last update on 2024-03-13 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...